canon ir1600 - prints but retries paper 3 or 4 times

[teckat]

is it possible u have a Cassette Feeding Assembly-K1
look on back of unit ???????????

how is the registration lead edge on copies ??

does it wander on copies

[teckat]

Intermittent 0202 Jam Code

it maybe necessary to adjust the pressure on the separation roller (P/N FF6-1621-000) from the cassette/cassettes that the jam has occurred.
To either increase or decrease the pressure on the separation roller, move the torsion spring (P/N FB6-1902- 000) up or down one notch on the guide plate (see Figure 1 pic).
Note: This adjustment is not found in the in the service manual.

Move Torsion Spring down (to left) a notch to decrease separation pressure.

Move Torsion Spring up (to right) a notch to increase separation pressure.

spring.JPG

Note: In addition to the previously mentioned separation spring adjustment, tie wraps may also cause this problem to occur.
The following procedure is suggested only if the separation spring adjustment does not resolve the issue.

PROCEDURE:
Remove the rear feeder panel; P/N FB6-1607-000 and carefully remove all the tie wraps coming off the Feeder Driver Assembly; P/N FG6-8648-000 (see Figure 2 pic).
tie wrap.JPG

[vikasarch]

Intermittent 0202 Jam Code

it maybe necessary to adjust the pressure on the separation roller (P/N FF6-1621-000) from the cassette/cassettes that the jam has occurred.
To either increase or decrease the pressure on the separation roller, move the torsion spring (P/N FB6-1902- 000) up or down one notch on the guide plate (see Figure 1 pic).
Note: This adjustment is not found in the in the service manual.

Move Torsion Spring down (to left) a notch to decrease separation pressure.

Move Torsion Spring up (to right) a notch to increase separation pressure.

spring.JPG

Note: In addition to the previously mentioned separation spring adjustment, tie wraps may also cause this problem to occur.
The following procedure is suggested only if the separation spring adjustment does not resolve the issue.

PROCEDURE:
Remove the rear feeder panel; P/N FB6-1607-000 and carefully remove all the tie wraps coming off the Feeder Driver Assembly; P/N FG6-8648-000 (see Figure 2 pic).
tie wrap.JPG

Dear teckat,

Will reply as soon as i follow your instructions.

Regards
Vikas

[teckat]

Dear teckat,

Will reply as soon as i follow your instructions.

Regards
Vikas

---____---
Be very careful cutting ties \ replace them _& do not tighten

[vikasarch]

A very happy and prosperous new year 2014 to you.

[montana]

Intermittent 0202 Jam Code

it maybe necessary to adjust the pressure on the separation roller (P/N FF6-1621-000) from the cassette/cassettes that the jam has occurred.
To either increase or decrease the pressure on the separation roller, move the torsion spring (P/N FB6-1902- 000) up or down one notch on the guide plate (see Figure 1 pic).
Note: This adjustment is not found in the in the service manual.

Move Torsion Spring down (to left) a notch to decrease separation pressure.

Move Torsion Spring up (to right) a notch to increase separation pressure.

spring.JPG

Note: In addition to the previously mentioned separation spring adjustment, tie wraps may also cause this problem to occur.
The following procedure is suggested only if the separation spring adjustment does not resolve the issue.

PROCEDURE:
Remove the rear feeder panel; P/N FB6-1607-000 and carefully remove all the tie wraps coming off the Feeder Driver Assembly; P/N FG6-8648-000 (see Figure 2 pic).
tie wrap.JPG

hi mr tekcat....please could explain the relation between these tie wraps and this issue...thank you with best wishes for a happy new year

[teckat]

That was a point mentioned by Canon\
I have seen neumerious issues caused by over-tighten tie wraps on many models-
When u pinch a signal wire -u effect restinance _it's like bending a water hose at full preasure--