Require step by step guide to upgrade the firmware in iR2545

[Rakesh]

Dear All

i need a step by step guide for upgrading firmware in the Canon iR2545 & iR Adv 2220 Copier.

any suggestion?

Thanks

[Tonerbomb]

Dear All

i need a step by step guide for upgrading firmware in the Canon iR2545 & iR Adv 2220 Copier.

any suggestion?

Thanks

RTFM !if you don't have the manual paul@justmanuals.com can hook you up.....

[JustManuals]

http://www.justmanuals.com/canon-ima...f-p-22381.html http://www.justmanuals.com/canon-cop...f-p-22348.html $12.77 each and instant download.

[teckat]

Dear All

i need a step by step guide for upgrading firmware in the Canon iR2545 & iR Adv 2220 Copier.

any suggestion?

Thanks

-------------------------------------

update the imageRUNNER ADVANCE System Software in Service Mode -

Go into service mode level 1 by pressing the Settings / Registration button, then 2 & 8 at the same time, then the Settings / Registration Button again. Press the Updater button.

Note: If Updater does not appear on this screen, make sure to activate eRDS.
Ensure proper IP address, Subnet Mask, Gateway and DNS settings before attempting to enable eRDS.

Select Mode List > Copier > Function > Install. Set eRDS to 1, then press OK. Select COM-TEST and select OK. Communication with the UGW server is necessary for Updater to work. This will not be available until COM-TEST result is OK!.

Select Mode List > Copier > Option > FNC-SW: Set CDS-FIRM to 1 and Set CDS-UGW to 1.


2. Press the Update Firmware button.
3. Press Confirm Applicable Firmware button.
4. Wait until the CDSUpdater screen appears again.
5. Press the Applicable Firmware down arrow.
6. Select the firmware version.
7. Press Next.
8. Press OK to start download of system software.
9. Press Accept to continue.
10. Wait until the status bar pops up and the Downloaded Completed screen appears then press OK.
11. Press Apply Firmware.
12. Press Yes to continue
13. The printer will restart itself when the upgrade is completed.
If the following message' Operations are already being performed by another user. Wait a moment ' appears at any point during the System Software Upgrade, shut down then restart the printer and try the upgrade again.

--------------------------------------------------------------------------------------------
imageRUNNER 2525 / 2530 / 2535 / 2535i / 2545 / 2545i
start the UST to load System Software
When reaching the point where the download instructions state to "Start up the UST", you must go to the sub-directory where the SSW is stored and choose the EXE file. When you double click on the EXE file the UST will open.

Upgrading Copier SSW on the iR2545 device imageRUNNER 2525 / 2530 / 2535 / 2535i / 2545 / 2545i process of flashing the copier's bootrom and system software below shows an overview of what tool is used to flash certain device components. Bootrom, DCON and Main controller is flashed through Canon User Support Tool (UST). The Finisher controller PCB is flashed using Canon Service Support Tool (SST) F

[Rakesh]

very helpful.

thank you very much tekcat

Rakesh



Sent from my Samsung Galaxy Note II

[purwoto]

-------------------------------------

update the imageRUNNER ADVANCE System Software in Service Mode -

Go into service mode level 1 by pressing the Settings / Registration button, then 2 & 8 at the same time, then the Settings / Registration Button again. Press the Updater button.

Note: If Updater does not appear on this screen, make sure to activate eRDS.
Ensure proper IP address, Subnet Mask, Gateway and DNS settings before attempting to enable eRDS.

Select Mode List > Copier > Function > Install. Set eRDS to 1, then press OK. Select COM-TEST and select OK. Communication with the UGW server is necessary for Updater to work. This will not be available until COM-TEST result is OK!.

Select Mode List > Copier > Option > FNC-SW: Set CDS-FIRM to 1 and Set CDS-UGW to 1.


2. Press the Update Firmware button.
3. Press Confirm Applicable Firmware button.
4. Wait until the CDSUpdater screen appears again.
5. Press the Applicable Firmware down arrow.
6. Select the firmware version.
7. Press Next.
8. Press OK to start download of system software.
9. Press Accept to continue.
10. Wait until the status bar pops up and the Downloaded Completed screen appears then press OK.
11. Press Apply Firmware.
12. Press Yes to continue
13. The printer will restart itself when the upgrade is completed.
If the following message' Operations are already being performed by another user. Wait a moment ' appears at any point during the System Software Upgrade, shut down then restart the printer and try the upgrade again.

--------------------------------------------------------------------------------------------
imageRUNNER 2525 / 2530 / 2535 / 2535i / 2545 / 2545i
start the UST to load System Software
When reaching the point where the download instructions state to "Start up the UST", you must go to the sub-directory where the SSW is stored and choose the EXE file. When you double click on the EXE file the UST will open.

Upgrading Copier SSW on the iR2545 device imageRUNNER 2525 / 2530 / 2535 / 2535i / 2545 / 2545i process of flashing the copier's bootrom and system software below shows an overview of what tool is used to flash certain device components. Bootrom, DCON and Main controller is flashed through Canon User Support Tool (UST). The Finisher controller PCB is flashed using Canon Service Support Tool (SST) F

Hi teckat, may I ask for a little guidance. I have tried updating the firmware and I succeeded. when I tried to swap bootroom with another machine instead the machine could not be turned on. and when I return the machine still cannot be turned on. what should i do so that the machine returns to normal.

[teckat]

[QUOTE=purwoto;743132]Hi teckat, may I ask for a little guidance. I have tried updating the firmware and I succeeded. when I tried to swap bootroom with another machine instead the machine could not be turned on. and when I return the machine still cannot be turned on. what should i do so that the machine returns to normal.[/QUOT ?

U removed Flash Rom

[purwoto]

[QUOTE=teckat;743140]

Hi teckat, may I ask for a little guidance. I have tried updating the firmware and I succeeded. when I tried to swap bootroom with another machine instead the machine could not be turned on. and when I return the machine still cannot be turned on. what should i do so that the machine returns to normal.[/QUOT ?

U removed Flash Rom

because my other machine died, by swapping the flash room I hoped the machine would turn on both of them.

[teckat]

[QUOTE=purwoto;743142]

because my other machine died, by swapping the flash room I hoped the machine would turn on both of them.

---

imageRUNNER boots to no display, green led on and no engine rotation.


There are several scenario's that may cause this condition:

1. If the Boot Rom is not seated properly or defective.
2. If the DC Controller is defective.
3. If J210 (DC Cont) / J8112 (Main Cont) is not connected.
4. If the Main Controller is defective.

EXAMPLE >>>> Through testing, it was found that voltage was missing off J8125 (Main Controller) when the imageRUNNER is in the blank display, green led on and no rotation state.

On a fully working device, J8125 (Main Controller) measures as follows:

Pin 1 - 0v 7 - 5v
2 - 3.2v 8 - 5v
3 - 3.2v 9 - 5v
4 - 0v 10 - 0v
5 - 0v 11 - 24v
6 - 0v

When the iR is in Blank display, green led on and no rotation or if DC Controller or BootRom is defective or J210 or J8112 is not connected.
J8125 measures as follows:

Pin 1 - 0v 7 - 5v
2 - 3.2v 8 - 0v
3 - 3.3v 9 - 0v
4 - 0v 10 - 0v
5 - 0v 11 - 0v
6 - 0v



If the imageRUNNER is in the Blank Display state and listed voltage is missing on J8125, there is no way to isolate the issue to one of the listed components.

Start with cleaning and re-seating the Boot Rom, reseat connectors J210, J8112 & J8125, cut any wire ties on the related harness.

This instance of the Blank Display was resolved by replacing the Boot Rom.


Part number for the Boot Rom: FM1-B884-000

[purwoto]

[QUOTE=teckat;743148]

---

imageRUNNER boots to no display, green led on and no engine rotation.


There are several scenario's that may cause this condition:

1. If the Boot Rom is not seated properly or defective.
2. If the DC Controller is defective.
3. If J210 (DC Cont) / J8112 (Main Cont) is not connected.
4. If the Main Controller is defective.

EXAMPLE >>>> Through testing, it was found that voltage was missing off J8125 (Main Controller) when the imageRUNNER is in the blank display, green led on and no rotation state.

On a fully working device, J8125 (Main Controller) measures as follows:

Pin 1 - 0v 7 - 5v
2 - 3.2v 8 - 5v
3 - 3.2v 9 - 5v
4 - 0v 10 - 0v
5 - 0v 11 - 24v
6 - 0v

When the iR is in Blank display, green led on and no rotation or if DC Controller or BootRom is defective or J210 or J8112 is not connected.
J8125 measures as follows:

Pin 1 - 0v 7 - 5v
2 - 3.2v 8 - 0v
3 - 3.3v 9 - 0v
4 - 0v 10 - 0v
5 - 0v 11 - 0v
6 - 0v



If the imageRUNNER is in the Blank Display state and listed voltage is missing on J8125, there is no way to isolate the issue to one of the listed components.

Start with cleaning and re-seating the Boot Rom, reseat connectors J210, J8112 & J8125, cut any wire ties on the related harness.

This instance of the Blank Display was resolved by replacing the Boot Rom.


Part number for the Boot Rom: FM1-B884-000

well, thank you very much for your knowledge. I have measured the voltage at pin j8125 and the result is

8 : 0v
9 : 0v
11: 0v

What is the price of Boot Room. my email is rohmansyaiful32@yahoo.com.
if there is a manual for repairing the mainboard or DC controller, it may also be offered to me.