IRA C5255 E102-101

[IkeW0491]

Hi all,

I can't seem to find my IRA 5255 SM

Can anyone tell me what the E102-101 means?

FYI I just installed a New DC-PCB on this machine, turned it on and got this error.


I have a C5051 SM, but there is no E102-101

Thanks in advance.

IKE

[RHodg57]

E102-101

Title Faulty EEPROM of YM-side Scanner
Description In the case of an error in reading EEPROM in the Laser
Driver (YM) or in the case of a wrong Laser Scanner Unit
which does not match with the Host Machine.
Remedy 1. Turn OFF and then ON the power.
2. Check the connector of the Laser Scanner Unit 1
3. Replace the Laser Scanner Unit 1.

[IkeW0491]

Hey guys!!

First of all I must be deslexic ( it is a 5051 ) LOL

As for the issue with the laser, I took out the ITB and Drums and removed the laser unit, double checked the cables and reconnected everything.
Reinstalled laser, drums and ITB.

Powered it back on, no more E00102-0101, however I am still getting the original error I ordered the DC PCB for
E001-003.

ARRRRGH!!!!!

IKE

[RHodg57]

E-001-003
Title High temperature error detected by hardware
Description Hardware detects abnormal high temperature of the
Thermistor (Main Thermistor 1: 264 deg C, Main Thermistor
2: 265 deg C, Sub Thermistor 1, 2: 280 deg C) for 400 msec
consecutively.
Remedy 1. If the detected temperature of the Thermistor is less than
the abnormal high temperature specified for Thermistor,
go through the following to clear the error: COPIER >
FUNCTION > CLEAR > ERR; and then turn OFF and then
ON the power.
If it’s at abnormally high temperature, do not turn on the
power before replacing the Film Unit.
2. Replace the Film Unit
3. Replacement of the Shutter Unit
4. Go through the following to check drive of FM5 and
FM6: COPIER > FUNCTION > PART-CHK > FAN; if the not
working properly, replace the fan.
5. Replace the DC Controller PCB (UN1)
NOTE: After performing the above remedy work, go through
the following to clear the error: COPIER > FUNCTION >
CLEAR > ERR

[IkeW0491]

Thanks Rhodg:

I already did all those things and that is why I ordered a new DC PCB,

I put the new (or supposedly new) PCB in and I am still getting the same error.

One thing about the PCB is that the BOX had (return to stock written on it), so not sure if it was new, or an older one
that was sent back because the new one didn't fix the original issue.

HMMM Anything else I can check to verify what the issue is with this??

Thanks again for all help

IKE

E-001-003
Title High temperature error detected by hardware
Description Hardware detects abnormal high temperature of the
Thermistor (Main Thermistor 1: 264 deg C, Main Thermistor
2: 265 deg C, Sub Thermistor 1, 2: 280 deg C) for 400 msec
consecutively.
Remedy 1. If the detected temperature of the Thermistor is less than
the abnormal high temperature specified for Thermistor,
go through the following to clear the error: COPIER >
FUNCTION > CLEAR > ERR; and then turn OFF and then
ON the power.
If it’s at abnormally high temperature, do not turn on the
power before replacing the Film Unit.
2. Replace the Film Unit
3. Replacement of the Shutter Unit
4. Go through the following to check drive of FM5 and
FM6: COPIER > FUNCTION > PART-CHK > FAN; if the not
working properly, replace the fan.
5. Replace the DC Controller PCB (UN1)
NOTE: After performing the above remedy work, go through
the following to clear the error: COPIER > FUNCTION >
CLEAR > ERR