firmware for irc 5185i

[win32]

Hello everyone, my CANON IRC 5185i does not print, but copies correctly,, when I start printing from the computer, or test page local printing machine, the printer stops and then restarts, j cleaned all the components electronics parts ;;; changed a ;memory card RAM, but the problem remains, I think a reinstall the firmware,, please if someone can direct me to find the firmware it'll be very nice thank you

[teckat]

Hello everyone, my CANON IRC 5185i does not print, but copies correctly,, when I start printing from the computer, or test page local printing machine, the printer stops and then restarts, j cleaned all the components electronics parts ;;; changed a ;memory card RAM, but the problem remains, I think a reinstall the firmware,, please if someone can direct me to find the firmware it'll be very nice thank you

================================

Your reboot only occurs when printing from the network

the sub R-A PCB could be faulty.

R-A PCB.JPG
i would also check that sub RB-A pcb/ remove and re-seat
known as the UFRII pcb.(standard print kit in "i" series/ unless u disabled it to install a imagePass Fiery H1

if u installed a H1 Fiery> slot #1 will have a sub RA-O (Open IF PCB) for Fiery
remove & re-seat it >also check ot's I/F Cable if this applies to you

also check the FIX UNIT temp readings/ have seen this on a few of these models/ when sending Prints .

have u tried using a Laptop to Print ?

[win32]

I cleaned PCB (Sub RA),,,,,,, (Sub RB-A), I tried to print via laptop,, the problem persists, I think to try cleaning SRAM,,,, ??????

[teckat]

I cleaned PCB (Sub RA),,,,,,, (Sub RB-A), I tried to print via laptop,, the problem persists, I think to try cleaning SRAM,,,, ??????

----------------------
Try this Clear here

COPIER>FUNCTION>CLEAR

ERDS-DAT = Embedded-RDS SRAM data clear
SCM data in the embedded-RDS SRAM are restored to the factory settings.
================================================== ===============



before u clear anything> u need to print out P PRINTS >that have settings needed to re-input
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>

RCON or DCON clear is a waste of time for your issue-------

----------------------------------------------------------
Also this MMI & MN-CON is a waste also> don't do it

MMI = Clears following user mode setting values:
- Backup data for copy operation panel (user-set values)
- Common settings backup data (user-set values)
- Backup data (except fax data) (user-set values)
The setting values are cleared after the main power switch is turned OFF/ON.
Operation method
1) Select this item, then press the OK key.
2) Turn the main power OFF/ON.
----------------------------------------------------------------------------------------------------------------------
MN-CON = Clears RAM on main controller PCB's SRAM board.
- The RAM is cleared after the OK key is pressed.
- Performing this item initializes all the data on the SRAM board. In other words, file management information for the hard disk is initialized, and image data on the hard disk can no longer be read.
Before performing this item, explain to the user that all images in the BOX will be lost, and receive permission to perform.
Operation method
1) Select COPIER > FUNCTION > MISC-P > P-PRINT to print out the service mode setting values.
2) Select this item, then press the OK key.

================================================== ============================================

[win32]

hello teckat the problem steel the same , but i missed to talk about something "" when i run the print job "" i have some works with NG ( #852 ) i think it's an memory truble bcause is there more than 5000 works ,,,, now i need to know how i can erase all of theese works , in sav i tried with many cleaning but i didn't found the good clean to erase it thank you

[teckat]

hello teckat the problem steel the same , but i missed to talk about something "" when i run the print job "" i have some works with NG ( #852 ) i think it's an memory truble bcause is there more than 5000 works ,,,, now i need to know how i can erase all of theese works , in sav i tried with many cleaning but i didn't found the good clean to erase it thank you

----------

Try clearing in RUI, open browser, type in Printer IP address to open, see if u can clear jobs

Make sure u don't have lower issues interupting jobs.

[win32]

please can you give me more details , how can i get in rui....

[teckat]

please can you give me more details , how can i get in rui....

)))));
Does your printer have an IP address ?
Are u networked, if so type it in the address bar of a browser.(IE, Firefox,Chrome).

[win32]

no i never print with network , i use only usb ,,,,,, but recently an technical's comming may be he tried to insert an ip adress ,, please tell me what i have to do in both cases , and how can i be sure that the machine are networked or no ,, thank you

[win32]

i'd like to know how to erase all print job from the hd,,,,,,there must be a way to do it ,, "" the hd was reinitialized but the print job still in the machine !!!!