Thanks Thanks:  0
Dislikes Dislikes:  0
Results 1 to 4 of 4
  1. #1
    Technician
    Join Date
    Jul 2013
    Posts
    27
    Rep Power
    22

    After install IP Board.

    After change IP Bord in IR2016 Error code display 354.(IP Bord is changed due to download standby display, not solved by installing firmware).Is need to change counter PCB OR DC Control PCB?

  2. #2
    Master Of The Obvious 10,000+ Posts
    After install IP Board.

    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    22,445
    Rep Power
    462

    Re: After install IP Board.

    If you do need to change the counter PWB you'll need the cooperation and consent of Canon. You can not exchange a counter PWB from another machine. You'll get a fatal error, and your machine effectively becomes a doorstop (brick).

    If you are an authorized Canon dealer, Great. Go to it. If you're not an authorized Canon dealer you will need the help of one. =^..^=
    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.
    3) if you're going to ask about jams include the jam code.
    4) if you're going to ask about an error code include the error code.
    5) You are the person onsite. Only you can make observations.

    blackcat: Master Of The Obvious =^..^=

  3. #3
    Service Manager 10,000+ Posts
    After install IP Board.

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244

    Re: After install IP Board.

    Quote Originally Posted by Guna View Post
    After change IP Bord in IR2016 Error code display 354.(IP Bord is changed due to download standby display, not solved by installing firmware).Is need to change counter PCB OR DC Control PCB?
    -------------------------------------------------------
    Counter Memory PCB / FM2-2799-000
    COUNTER.JPG

    Check J315 on the image processor pcb. The code can be displayed when there is no connection between the serial pcb and the image processor.

    Check for good connection first. If there is a fax pcb on the unit, it will have to be removed in order to locate J315.


    READ PDF





    The imageRUNNER 1023/1023N/1023iF/2016/2020/2016i/2020i model does not have a Main Controller PCB.
    The Counter Memory PCB is instead mounted to the Image Processor PCB.

    E354

    1. Mismatch or absence of the serial number stored in the Serial Number PCB and Main Controller /Image Processor PCB or Counter Memory
    PCB (mismatch of two serial numbers).
    2. Absence of serial numbers in both Main Controller PCB (SRAM) or Counter Memory PCB
    ------------------------
    1. Put back all original PCBs into the equipment!
    2.Do not utilize a used Counter Memory PCB or Serial Number PCB from any other equipment.
    3. After “Prohibited Action” has been corrected, perform “E354 CLR”.
    (FUNCTION>CLEAR>E354-CLR) then cycle power off and on.
    (For “70” series and later see Note #3.
    For imageRUNNER 1023/ 1023N/1023iF/2016/ 2020/ 2016i/2020i see step # 10 under “Servicing”).

    10. In some cases, on the imageRUNNER 1023/ 1023N/ 1023iF/ 2016/ 2020/ 2016i/ 2020i after replacing the Counter Memory PCB, an E354 or E355 code may appear. At this point, enter service mode then scroll to “CLEAR”. Press “OK”, then scroll to “ERR”. Press “OK”, then an E355 will appear. Wait ten (10) seconds until “E355 CLEAR” is completed. Then cycle the main power.
    Attached Files Attached Files
    Last edited by teckat; 09-01-2014 at 06:18 PM.
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  4. #4
    Service Manager 10,000+ Posts
    After install IP Board.

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244

    Re: After install IP Board.

    Procedure after Replacing the Image Processor PCB
    iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i

    After replacing the image processor PCB with a new one, input the all value printed on the service label affixed to the rear cover.
    Make the following adjustments:
    - Correction of output between CIS channels
    1) Enter the service mode.
    Sequentially press the User Mode key "*", 2 key, 8 key, and User Mode key "*" on the operation panel.
    2) Using the arrow keys on the operation panel, display "TEST MODE".
    3) Press the OK key.
    4) Press the 2 key. "SCAN TEST" appears.
    5) Press the 1 key.
    After completion of the above steps, contact sensor output correction will be performed and parameters will be set automatically.
    - Read position adjustment (Stream reading: Only when the ADF is installed)
    1) Enter the service mode.
    Press the User Mode key "*", 2 key, 8 key, User Mode key "*" on the operation panel of the host machine.
    2) Using the arrow keys on the operation panel, display "TEST MODE".
    3) Press the OK key.
    4) Press the 2 key. "SCAN TEST" appears.
    5) Press the 3 key. "SHEET POS ADJ" appears.
    The optical system starts scanning. Several seconds later, automatic adjustment of the reading position finishes and "OK" appears.
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here