Likes Likes:  0
Dislikes Dislikes:  0
Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 24
  1. #11
    Service Manager 10,000+ Posts
    Canon IR Advance C9075 Pro - Enabling/Initializing Finisher

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244

    Re: Canon IR Advance C9075 Pro - Enabling/Initializing Finisher

    Quote Originally Posted by Taggerung08 View Post
    Okay, walking up to the machine and testing each function 1 by 1 the following does not work.

    Hole punching
    Folding
    Saddle stitching (middle staples, etc.)
    Collating
    -----------------
    paper exits with
    no jams>no errors>no alarms

    Limited Functions is not showing on panel

    re-load firmware
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  2. #12
    Field Supervisor 500+ Posts roho's Avatar
    Join Date
    Mar 2009
    Location
    Earth
    Posts
    844
    Rep Power
    43

    Re: Canon IR Advance C9075 Pro - Enabling/Initializing Finisher

    a mmi clear might be needed as well. If one wasn't done at set up, strange symptoms can pop up like this. Try firmware first though.

  3. #13
    Service Manager 10,000+ Posts
    Canon IR Advance C9075 Pro - Enabling/Initializing Finisher

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244

    Re: Canon IR Advance C9075 Pro - Enabling/Initializing Finisher

    forgot about MMI

    check panel operation for options after firmware re-load>then

    Select "Prioritize Finishing" Settings of Drivers and click OK.
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  4. #14
    Field Supervisor 500+ Posts roho's Avatar
    Join Date
    Mar 2009
    Location
    Earth
    Posts
    844
    Rep Power
    43

    Re: Canon IR Advance C9075 Pro - Enabling/Initializing Finisher

    I clear mmi on every setup, and I've had many strange issues before that suddenly disappear after clearing it. However, I'd go Firmware first, figured it's worth a mention.

  5. #15
    Service Manager 10,000+ Posts
    Canon IR Advance C9075 Pro - Enabling/Initializing Finisher

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244

    Re: Canon IR Advance C9075 Pro - Enabling/Initializing Finisher

    Note: Before Clearing the MMI/Copy Mode, be sure to Print Out the machine User Data List and P-Print.
    All user mode Settings: ID Modes, ID Group, Passwords, Mode Memory and the IP Address are cleared.

    Before clearing MMI, print out an Output Report via Settings/Registration > Preferences > Network > Output Report.
    Next go to Copier > Function > Clear > MMI clear > OK, then Power cycle machine Off and then back On.


    Re-enter Network information:
    Go to Preferences > Confirm Network connection Set changes and Turn On > TCP/IP settings > IPv4 Settings > IP Address Settings and re-enter information. Close the window and re-boot copier to a working condition===


    Hopefully! !!!
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  6. #16
    Trusted Tech 50+ Posts Taggerung08's Avatar
    Join Date
    Sep 2014
    Posts
    60
    Rep Power
    20

    Re: Canon IR Advance C9075 Pro - Enabling/Initializing Finisher

    Quote Originally Posted by teckat View Post
    Note: Before Clearing the MMI/Copy Mode, be sure to Print Out the machine User Data List and P-Print.
    All user mode Settings: ID Modes, ID Group, Passwords, Mode Memory and the IP Address are cleared.

    Before clearing MMI, print out an Output Report via Settings/Registration > Preferences > Network > Output Report.
    Next go to Copier > Function > Clear > MMI clear > OK, then Power cycle machine Off and then back On.


    Re-enter Network information:
    Go to Preferences > Confirm Network connection Set changes and Turn On > TCP/IP settings > IPv4 Settings > IP Address Settings and re-enter information. Close the window and re-boot copier to a working condition===


    Hopefully! !!!

    Update:

    Firmware successfully upgraded.

    Decks 1-2 are reading A-4 sized paper even though there is Letter loaded in both and they are both set to Letter. So if you choose to do finishing options from deck 1-2 it will not work, the only option that work from the decks is corner stapling.

    Tray 3 has Letter R. From this tray the folding/saddle stitching works. Setting the tray to Letter, the hole punch and middle stapling works.

    So I think I'm getting close.

    This machine also has a imagepass gx300 so do I have to unplug the server? Is there some precaution I should take before clearing the MM1? Or should I just leave it as I reset the MMI and renter the user settings.

    Thanks

  7. #17
    Service Manager 10,000+ Posts
    Canon IR Advance C9075 Pro - Enabling/Initializing Finisher

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244

    Re: Canon IR Advance C9075 Pro - Enabling/Initializing Finisher

    Problem :
    The Left and Right Deck are reading A4 paper size with LTR size loaded.

    Solution :
    Set the following settings in service mode to remedy the issue:

    (Lv.1) COPIER > OPTION > CST > P-SZ-C1 (Right Deck Paper setting)
    (Lv.1) COPIER > OPTION > CST > P-SZ-C2 (Left Deck Paper setting)

    Setting Value

    0: A4 (default), 1: B5, 2: LTR
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  8. #18
    Service Manager 10,000+ Posts
    Canon IR Advance C9075 Pro - Enabling/Initializing Finisher

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244

    Re: Canon IR Advance C9075 Pro - Enabling/Initializing Finisher

    U only have certain combinations that will be available depending on paper size

    Make sure u use the Correct print drivers for GX300 when printing from network----

    GX300 DRIVERS LINK

    Canon U.S.A. : Support & Drivers : ColorPASS-GX300

    Note: for GX300
    Problem :
    When Fiery PS driver are installed for the first time, finishing options such as hole punch can be selected, but the document will print without being hole punched.


    Solution :

    1. If selecting the update button, from the Configuration tab in the printer properties menu, does not resolve the issue, unselect the Two-Way Communication box and click on the Defaults button.

    2. Most of the Installed Options will be cleared. Select the Two-Way Communication box and click the Update Button.

    3. The Installed Options box should now be populated. Click Apply and Ok, and finishing option, such as hole punch will now work
    Last edited by teckat; 09-18-2014 at 02:54 AM.
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  9. #19
    Service Manager 10,000+ Posts
    Canon IR Advance C9075 Pro - Enabling/Initializing Finisher

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244

    Re: Canon IR Advance C9075 Pro - Enabling/Initializing Finisher

    All imagePASS Series , All imagePRESS Series, ColorPASS GX-100, GX-200, GX-300, GX-400
    Finishing Options Can Be Selected On The PS Driver When First It Is First Installed, But Do Not Printout With Finishing Options.




    When Fiery PS driver are installed for the first time, finishing options such as hole punch can be selected, but the document will print without being hole punched.



    1. If selecting the update button, from the Configuration tab in the printer properties menu, does not resolve the issue, unselect the Two-Way Communication box and click on the Defaults button.




    2. Most of the Installed Options will be cleared. Select the Two-Way Communication box and click the Update Button.




    3. The Installed Options box should now be populated. Click Apply and Ok, and finishing option, such as hole punch will now work.

    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  10. #20
    copymanpete
    Guest

    Re: Canon IR Advance C9075 Pro - Enabling/Initializing Finisher

    I may over simplifying this but is the machine in limited functions mode?

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here