Dear all ,
i just to take some feed back about this series of machines IRA6055/75 is theres any disadvantage befor i buy some? thank you
Dear all ,
i just to take some feed back about this series of machines IRA6055/75 is theres any disadvantage befor i buy some? thank you
Distinguished road makes you jewel in rough
Canon printers always have issues [:-$
-New Type Lower Fixing Roller Pressure Roller to Address Paper Creasing.
-Improper Toner Bottle Installation.
-PICO Fuse Voltage Distribution for the Main Driver and Relay PCB.
-Change in the Paper Level Sensor to Prevent Jamming.
-Countermeasures Against the Failure of Detecting Various Jams and Errors.
-Countermeasure Against Adhesion of Foreign Objects in the Developing Assembly.
-Noise / Image Faults Caused by the Screws of the Drum Drive Assembly Loosening or Coming Off.
-E302-0101 .
-Damaged Belt Handle.
-Minimizing Early Failure of the Thrust Retainer Rings and/or Bushings.
-Fixing Inlet Sensor Flag.
-Countermeasure Against 0215/ 0208/ 0209 Jam Codes and Paper Skew.
-Permanent Countermeasure Against Breakage of the Operator Lever for the Toner Bottle.
-Permanent Countermeasure to Prevent a Half-Locked Right Door Assembly.
-Permanent Countermeasure to Prevent LDGR or Larger Paper Size Corner Cut.
-Measure Against the Failure of Attaching the Toner Bottle.
-Measure Against 0104, 0105, 0208 or 0209 Jams.
-Measure Against 0113/ 0213 Jams.
-Countermeasure to Prevent the Thrust Retainer Ring from Detaching or Breaking.
-0105 Jam / Paper Skew Countermeasure Because of Damaged to the Registration Assembly.
-E748-2012 Error Code.
-External Heating Assembly: Modification to Termistor Wire Clamp.
-Light Density Image Fault Due to a Defective Developing High Voltage Contact.
-E066-002 Error Code.
-E017-0001 / E017-0003 Error Codes.
-Paper Feed Lines When Scanning Originals Via DADF.
-ADF Multi-feeding Permanent Countermeasure.
-Modification to the Release Lever of the Fixing Feeder Lock Handle Unit .
-New Style Cleaning Blade to Address Spots and Blade Lines (Revised).
-Permanent Countermeasure Against Displacement of the Electrostatic Transfer Belt (ETB).
-Countermeasure to Minimize “Load Paper” Fault Message (Revised).
-Points to Note when Replacing the Main Controller.
-Troubleshooting Alarm Code 330025 and/or Intermittent Black Images.
-Spot Mark Identification and AP Kit Drum Cleaning Addendum.
-ETB Shift Temporary Countermeasure.
-Measures to Minimize the Deterioration and Failure of the "Belt, timing, Cogged" (Revised).
-Measure to Minimize the Failure of the Drum Cleaning Assembly Cogged Timing Belt.
-Change to the Paper Feed Rollers and the Catch Plate Due to Production Changes.
-0204/0208 Jam Code Countermeasure Procedure.
-Preventing Paper Pickup Slippage in the Right and Left Cassette Decks (Revised).
-E840 Error Code Avoidance and Proper Thrust Fixing Roller Retainer Attachment Procedure.
-Preventive Measure Against Damaged Fixing / Feeder Assembly Cable.
-Prevention of the Paper Pick-Up Roller from Coming Off.
Few more :'(
**Knowledge is time consuming, exhausting and costly for a trained Tech.**
i found all canon advanced series to be great....b&w and colour.
i have a few of the ira6075 in law offices...besides print shops law offices are high maintence clients but since we moves from minoltas to canon.
very few calls.
the ir adv6075 does have a wierd fixing assembly setup, but if you fallow the service manual for repairs..all ok
just watch out for the ir adv c5000 series..e075 errors. but once you get that fixed..all ok.
cheers
I have found that all of Canon's B&W Advance series to be pretty awesome overall.
Fixing assembly in the 6000/8000 was a pain when it first came out, had some issues, but that seems to be mostly resolved now!
Only things I regularly encounter are the fuser issues.
A few of those toner bottle issues and I have a waste toner pipe issues as well on one or two.
Otherwise they are pretty well problem free. They are in relatively low volume areas though!
Pickup jamming from deck only --Install modified pre-reg roller or assembly
For intermittent- erratic punching, I have had to replace 2 punch units to fix it, after trying motors, sensors and controllers.
Thanks for your help. There is an update for the Finisher [mount puncher*1x FM1-D540-000] Haven't seen an update for pre-reg rollers though, any PN handy please
I searched for the info before posting but could not find it. I am sure the pre-reg roller is just a suffix change -010 or 020.
I had the punch issues long before they released the info about changing the covers.
The two I fixed still have the original covers
also
For 0104/0105/0208/0209
There is a new sensor holder FL3-9005 below the multi paper pickup assy.
Old sensor allows nicks in the plastic
also
A damaged reg assembly causes 0105
You may see a couple bent pieces in the front and a white plastic tab out of place.
FM4-5156-020 modified reg assy.
Take your pre-reg assembly out , You may find some scraps of paper stuck in the metal guide, causing paper to hit it intermittently and cause a jam.
Bookmarks