Page 1 of 3 123 LastLast
Results 1 to 10 of 26
  1. #1
    Senior Tech 100+ Posts
    Join Date
    Dec 2011
    Location
    SALEM NJ
    Posts
    196
    Rep Power
    26

    Canon IR2200 taking too long to warm Up?

    Hi guys,
    I have a customer at a Church that claims it takes too long to warm up from power switch being turned om....this copier is in a Church that has no heat until Saturdays before services.
    The specifications say 29 seconds from power on, this machines is taking 2:35 according to my iphone stopwatch....any suggestions or should I just tell the customer its too cold in here!
    Haha
    Thanks,
    Doug

  2. #2
    Service Manager 10,000+ Posts
    Canon IR2200 taking too long to warm Up?

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244

    Re: Canon IR2200 taking too long to warm Up?

    Quote Originally Posted by doug View Post
    Hi guys,
    I have a customer at a Church that claims it takes too long to warm up from power switch being turned om....this copier is in a Church that has no heat until Saturdays before services.
    The specifications say 29 seconds from power on, this machines is taking 2:35 according to my iphone stopwatch....any suggestions or should I just tell the customer its too cold in here!
    Haha
    Thanks,
    Doug
    ================================================== ==============
    like having printer outside on curb

    * When main power is turned ON: 29 seconds max.
    *Activation time may vary depending on the conditions under which the machine is used. (In all cases, at a room temperature of 20°C.)

    20ºC = 68.000ºF


    ===================================
    Temperature Control

    Normal
    [1] Power-on sequence
    Used with pre-heating control if the reading of the main thermistor (TH1) is 100°C or lower during
    recovery from sleep mode/power-on/control panel input/document detection.


    &
    Clean _& Re-seat the Memory Dimms and Boot ROM as an added measure
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  3. #3
    Senior Tech 100+ Posts
    Join Date
    Nov 2014
    Location
    Mariupol
    Posts
    105
    Rep Power
    20

    Re: Canon IR2200 taking too long to warm Up?

    Quote Originally Posted by doug View Post
    Hi guys,
    I have a customer at a Church that claims it takes too long to warm up from power switch being turned om....this copier is in a Church that has no heat until Saturdays before services.
    The specifications say 29 seconds from power on, this machines is taking 2:35 according to my iphone stopwatch....any suggestions or should I just tell the customer its too cold in here!
    Haha
    Thanks,
    Doug
    You can try to clean the heating element, but don't forget to apply fuser film grease.

  4. #4
    Service Manager 10,000+ Posts
    Canon IR2200 taking too long to warm Up?

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244

    Re: Canon IR2200 taking too long to warm Up?

    Quote Originally Posted by Corder View Post
    You can try to clean the heating element, but don't forget to apply fuser film grease.
    ========================

    no room Heat in December > in New Jersey USA for an entire week until Saturday >

    Grease will not help that > unless u heat it on a stove
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  5. #5
    Senior Tech 100+ Posts
    Join Date
    Nov 2014
    Location
    Mariupol
    Posts
    105
    Rep Power
    20

    Re: Canon IR2200 taking too long to warm Up?

    Quote Originally Posted by teckat View Post
    ========================

    no room Heat in December > in New Jersey USA for an entire week until Saturday >

    Grease will not help that > unless u heat it on a stove
    No, but cleaning probably will

  6. #6
    Service Manager 5,000+ Posts
    Canon IR2200 taking too long to warm Up?

    copier tech's Avatar
    Join Date
    Jan 2014
    Location
    London
    Posts
    7,531
    Rep Power
    182

    Re: Canon IR2200 taking too long to warm Up?

    Does it hang at the boot up screen? More likely to be a HDD issue, if the machine was taking that long to warm up it would throw an E000 code etc
    Let us eat, drink, and be merry, because tomorrow we may die!

    For all your firmware & service manual needs please visit us at:

    www.copierfirmware.co.uk - www.printerfirmware.co.uk




  7. #7
    Service Manager 10,000+ Posts
    Canon IR2200 taking too long to warm Up?

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244

    Re: Canon IR2200 taking too long to warm Up?

    Quote Originally Posted by copier tech View Post
    Does it hang at the boot up screen? More likely to be a HDD issue, if the machine was taking that long to warm up it would throw an E000 code etc


    Good Pointon HDD-


    E000
    = 0000 /The reading of the main thermistor does not reach 30°C 1 sec after the main power switch is turned on. Or, it does not reach 70°C 2 sec thereafter.

    E002
    =0000 The temperature of the fixing film is as follows:
    1. has exceeded 100°C, but does not reach 115°C within 1 sec thereafter.
    2. has exceeded 140°C, but does not reach 150°C within 1 sec thereafter.
    3. has exceeded 160°C, but does not reach 165°C within 1 sec thereafter.

    his printer must be reaching these figures to prevent 000_002_??
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  8. #8
    Service Manager 5,000+ Posts
    Canon IR2200 taking too long to warm Up?

    copier tech's Avatar
    Join Date
    Jan 2014
    Location
    London
    Posts
    7,531
    Rep Power
    182

    Re: Canon IR2200 taking too long to warm Up?

    Exactly! 2 mins 34 seconds he'd deffo get a an error!
    Let us eat, drink, and be merry, because tomorrow we may die!

    For all your firmware & service manual needs please visit us at:

    www.copierfirmware.co.uk - www.printerfirmware.co.uk




  9. #9
    Master Of The Obvious 10,000+ Posts
    Canon IR2200 taking too long to warm Up?

    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    22,444
    Rep Power
    462

    Re: Canon IR2200 taking too long to warm Up?

    You can also get longer warm up times and fuser errors if the press roller bearings are coming apart, but never 2:34. =^..^=
    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.
    3) if you're going to ask about jams include the jam code.
    4) if you're going to ask about an error code include the error code.
    5) You are the person onsite. Only you can make observations.

    blackcat: Master Of The Obvious =^..^=

  10. #10
    Service Manager 10,000+ Posts
    Canon IR2200 taking too long to warm Up?

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244

    Re: Canon IR2200 taking too long to warm Up?

    Would like to ask poster what the control panel shows,
    ?? Slow Progress bar, Warming up, Wait or other.

    Note: reminder_
    Scanning originals while the machine is warming up, will cause warm up to take longer.)

    There was a series that had a extended wwarm up issue with finisher attached & no error.
    Remove finisher _printer came to ready_??
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here