i have cleaning transfer unit belt and now its ok
Thank you for everything teckat
i have cleaning transfer unit belt and now its ok
Thank you for everything teckat
hi teckat please can you help me because i have the problem with canon C2020 error code E025-0200
begging-dog.jpg
Teckat where are you? Please help....I have so many problems!
What have you done so far?
Practice makes perfect
If it ain't broke, don't fix it
A picture is worth a thousand words
If you want something done right, you have to do it yourself
]]]]]]]]]]]]]]]]]
There are a few E025 codes listed on the imageRUNNER ADVANCE series that Do Require a clear to be done.
Best practice for any E025-XXXX code on the imageRUNNER ADVANCE series is to clear the code in service mode and reboot the machine to see if it resets. If it does not clear, trouble shoot the device for that code. Always perform the clear after swapping or replacing any parts related to E025-xxxx codes.
E025 -0200
Toner bottle motor lock (M) error
Over-current of the toner container drive motor was detected.
1. Check whether a toner container of a different model is not installed.
If it is installed, replace it with a correct one.
1-1. Open the toner container installation inlet cover.
1-2. Manually turn the container in an counterclockwise direction until it is fully turned.
1-3. Rotate the toner container in an counterclockwise direction using a toner container removing tool.
1-4. The toner container is placed at the position where it can be removed. Remove the toner
container.
2. Check the connection of the toner container drive motor (M7/M10/M13/M16) (Check whether the wire is not caught by parts.)
3. Replace the toner container drive motor.
4. Replace the toner container tray unit (when this error occurred at rotation of the toner container).
5. Replace the hopper unit.
Inspect to see if Gear (FU6-0584-000), has cracked or broken (EXAMPLE as shown). This may cause E025 Error Codes and prevent the Toner Door from opening.
**Knowledge is time consuming, exhausting and costly for a trained Tech.**
thanks teckat the problem was at the engine of hopper cyan, but now i have a problem with copier c5051
i ,the error is. E020-014 how can i fix it...
=======================================
your 9070 error code was--0200 ?? that indicated Magenta & not Cyan
================================================== ==========================================
imageRUNNER ADVANCE C5030 / C5035 / C5045 / C5051 / C5235 / C5235A / C5240 / C5240A / C5250 / C5255
0100(Y), -0200(M), -0300(C), -0400(Bk)
????E020-014
-014X ??? 0 or 1
Error in Y Developing Assembly
ATR sensor (Y) (TS5)
are u trained on product ??? recommend to get manuals for the products u service
**Knowledge is time consuming, exhausting and costly for a trained Tech.**
canon iR2545 error E000000
canon iR2545 error E000000 i have change the fuser unit but the same if i have clear engime is ok, but for 20minutes error E000000 again
Please help me if you know
maybe it is time to start a new thread each time you change copier
================================
u cant' group all the different models u have issues with together in a single threaded post.
E000-0000 error code===To clear a Fuser Error enter Service Mode >CLEAR>ENGIN>ERRCLR
You must follow steps below to clear E000
Enter service mode by pressing additional functions than 2 than 8 and then Additional Functions.
#SSSW will be displayed.
Use the right arrow and scroll to #CLEAR then press OK.
Then Use the right arrow and scroll to ENGINE then press OK.
ERRCLR will be displayed then press OK. Then power cycle the machine.
-Your AC wall voltage was double checked and was within specifications. ??
-Make sure there is AC voltage being output to the fixing unit on connector J110.
Connector J110 is the AC connector which supplies AC voltage to the fixing film unit heater.
-If not u may have a Power Supply Assembly Issue.
Below are images that show the Power Supply Assembly location and connector J110's location.
The machine's lower left panel needs to be removed in order to access the Power Supply Assembly.
**Knowledge is time consuming, exhausting and costly for a trained Tech.**
20181107122254
20181107122236
i have this problem with my printer canon ir adv c9070pro.
i have change about 5 yellow developing unit and drum unit.
when i change it just print a few pages about 200 pages and goes again yellow like in document i have sent you.
any idea why that happens
Bookmarks