Results 1 to 7 of 7
  1. #1
    Trusted Tech 50+ Posts
    Join Date
    Aug 2013
    Location
    New Philadelphia, OH
    Posts
    91
    Rep Power
    0

    Bizhub 751 in a constant state of "warming up"

    Good Afternoon,

    I have a bizhub 751 that would not come out of the warming up phase on start up this morning. the machine has not produced an error code and I can access all functions via the control panel but it will not print, copy, or scan...the jobs just sit in the que. This machine has 190K on it and the drum was replaced on it last month by another tech. when I pulled the ADU tray I noticed toner all over the charge wire. Pulled the charge wire and cleaned. Both sensors under the charge wire were buried in toner...pulled sensors and cleaned. put everything back together and still won't come out of warming up state. Checked fuser for proper cycling...checked out ok...all 3 lamps lit and turned off...watched it thru 4 cycles. Checked toner bottle to be sure there was toner in it...half full. also checked all 4 motors to be sure they were turning freely and that none of the gears had been stripped off. I am having difficulty finding any reference to this issue in the manual...anybody seen this before? Thanks

  2. #2
    Vulcan Inventor of Death 1,000+ Posts Mr Spock's Avatar
    Join Date
    Aug 2006
    Location
    tampa,fl
    Posts
    2,067
    Rep Power
    63

    Re: Bizhub 751 in a constant state of "warming up"

    three things come to mind when I see this
    1. memory issue
    2. hard drive issue
    3. Temp sensors on the fuser.
    And Star Trek was just a tv show...yeah right!

  3. #3
    Senior Tech 100+ Posts
    Join Date
    Dec 2010
    Posts
    126
    Rep Power
    0

    Re: Bizhub 751 in a constant state of "warming up"

    Clean the sensors that are under the Drum.The toner control sensor board.

  4. #4
    Trusted Tech 50+ Posts
    Join Date
    Aug 2013
    Location
    New Philadelphia, OH
    Posts
    91
    Rep Power
    0

    Re: Bizhub 751 in a constant state of "warming up"

    Quote Originally Posted by Mr Spock View Post
    three things come to mind when I see this
    1. memory issue
    2. hard drive issue
    3. Temp sensors on the fuser.
    Thanks for the reply...I hadn't considered the fuser sensors...I'll check that tomorrow when I go back. I'll try disabling the HD for testing purposes but will have to order memory to test that.

  5. #5
    Trusted Tech 50+ Posts
    Join Date
    Aug 2013
    Location
    New Philadelphia, OH
    Posts
    91
    Rep Power
    0

    Re: Bizhub 751 in a constant state of "warming up"

    Quote Originally Posted by scottybbb View Post
    Clean the sensors that are under the Drum.The toner control sensor board.
    Thanks Scotty...I plan to pull drum and dev unit tomorrow...I also thought maybe the toner control board may be bad or needed cleaning.

  6. #6
    Senior Tech 250+ Posts
    Bizhub 751 in a constant state of "warming up"

    CraigW's Avatar
    Join Date
    Dec 2010
    Posts
    417
    Rep Power
    32

    Re: Bizhub 751 in a constant state of "warming up"

    ^^^^ and reseat it's connector.

  7. #7
    Trusted Tech 50+ Posts
    Join Date
    Aug 2013
    Location
    New Philadelphia, OH
    Posts
    91
    Rep Power
    0

    Re: Bizhub 751 in a constant state of "warming up"

    Thanks for all the replies (you nailed it scotty), it was in fact dirty sensors. I ended up cleaning the entire section including both sensors and TCSB. Machine fired up as it is supposed to but I do have a quality issue with it now. Toner on both sides of the page...order new developer unit...hope that is it because it is quite expensive.

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here