Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 8 of 8
  1. #1
    Trusted Tech 50+ Posts
    Join Date
    Jun 2011
    Location
    Smithtown
    Posts
    61
    Rep Power
    0

    OKI C9650 Transfer Belt Reset

    OKI C9650 Transfer Belt Reset i have no idea how to get into service mode or reset this damn code any ideas my tech brothers and sisters


  2. #2
    Senior Tech 100+ Posts
    OKI C9650 Transfer Belt Reset

    Lasersupplies's Avatar
    Join Date
    Jul 2011
    Location
    Belfast
    Posts
    172
    Rep Power
    0

    Re: OKI C9650 Transfer Belt Reset

    1) Power ON printer while holding "+(up)" & "-(down)" and "help" buttons until “OKIUSER” message apear in LCD....
    2) Press + or – button until “ENGINE DIAG MODE” is displayed;
    3) Press "ENTER", will be displayed "DIAGNOSTIC MODE XX.XX.XX S-MODE"
    4) Press + or – button until “NV-RAM INITIAL” is displayed
    5) Press "ENTER" again;
    6) Will appear "TABLE 1" message;
    7) Press "ENTER" until "EXECUTING RESET" message appear. the "NV-RAM INITIAL" message will BLINK...
    This procedure reset DRUM, FUSER and BELT...
    8) power OFF printer, wait 10 sec, and power ON again... =)

    Let me know


  3. #3
    Trusted Tech 50+ Posts
    Join Date
    Jun 2011
    Location
    Smithtown
    Posts
    61
    Rep Power
    0

    Re: OKI C9650 Transfer Belt Reset

    ok when i hold down those keys all that pops up is system maintenance and when i go into diag mode it doesn't give me the options you have listed ive tried scrolling in the system maintenance menu but to no avail any suggestions


  4. #4
    Service Manager 10,000+ Posts
    OKI C9650 Transfer Belt Reset

    JustManuals's Avatar
    Join Date
    Jan 2006
    Location
    Las Vegas, NV
    Posts
    10,041
    Rep Power
    141

    Re: OKI C9650 Transfer Belt Reset

    This Parts & Service manual can be purchased for $12.77 and downloaded immediately after payment from

    http://www.justmanuals.com

    Paul@justmanuals.com



  5. #5
    Trusted Tech 50+ Posts hekotez's Avatar
    Join Date
    Jan 2007
    Posts
    89
    Rep Power
    0

    Re: OKI C9650 Transfer Belt Reset

    If you dont know what you're doing... be careful with NV-Ram resets because depending on the machine's current FW... You might be half way to kill the printer's NIC firmware, amongst other things.
    And i cant see why you want/need to get ito SM to reset the counter...
    Get you hands dirty... and replace the reset fuse on the belt.


  6. #6
    Trusted Tech 50+ Posts
    Join Date
    Jun 2011
    Location
    Smithtown
    Posts
    61
    Rep Power
    0

    Re: OKI C9650 Transfer Belt Reset

    Quote Originally Posted by hekotez View Post
    If you dont know what you're doing... be careful with NV-Ram resets because depending on the machine's current FW... You might be half way to kill the printer's NIC firmware, amongst other things.
    And i cant see why you want/need to get ito SM to reset the counter...
    Get you hands dirty... and replace the reset fuse on the belt.


    lol "get your hands dirty" ive replaced most of the parts on this machine, but nothing was resetting itself... ask questions before responding with ignorance.... besides figured out the problem machine had a bad harness replaced and it allowed me to get into the mode i needed to get into before that the machine was locked up hence multiple errors on new units + parts


  7. #7
    Trusted Tech 50+ Posts hekotez's Avatar
    Join Date
    Jan 2007
    Posts
    89
    Rep Power
    0

    Re: OKI C9650 Transfer Belt Reset

    As far as i see it you're the ignorant one, else you wouldnt be here asking idiotic questions about how the system OKI uses to reset counters works, and after replacing a "bunch" of parts and the counter's not reseting, you find that quite natural and decide to do it thru service mode...
    Also maybe next time you should be more self explanatory on your post, as i see it you're the one needing help not me.
    If one needs to work with counters on that machine and others, there is a proper software to load/reset/import/export data,counters, configs etc.
    Once again i'll repeat myself, you shouldnt reset counters by reseting NV-Ram.


  8. #8
    Trusted Tech 50+ Posts
    Join Date
    Jun 2011
    Location
    Smithtown
    Posts
    61
    Rep Power
    0

    Re: OKI C9650 Transfer Belt Reset

    Quote Originally Posted by hekotez View Post
    As far as i see it you're the ignorant one, else you wouldnt be here asking idiotic questions about how the system OKI uses to reset counters works, and after replacing a "bunch" of parts and the counter's not reseting, you find that quite natural and decide to do it thru service mode...
    Also maybe next time you should be more self explanatory on your post, as i see it you're the one needing help not me.
    If one needs to work with counters on that machine and others, there is a proper software to load/reset/import/export data,counters, configs etc.
    Once again i'll repeat myself, you shouldnt reset counters by reseting NV-Ram.
    lol i wonder if you read what you write before you send it lmfao


Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-=-=-=-=-=-


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here