Thanks Thanks:  0
Dislikes Dislikes:  0
Page 1 of 2 12 LastLast
Results 1 to 10 of 11
  1. #1
    Service Manager 1,000+ Posts
    Customer called with RZ990 with error P98-947


    Join Date
    Aug 2007
    Location
    Brooklyn
    Posts
    1,323
    Rep Power
    48

    Thumbs up Customer called with RZ990 with error P98-947

    Customer has error P98-947 on RZ990. Have no experience on this but read that this code is related to loss of 24v and could be due to blown fuse in group A. Your help is very much appreciated. Frank/ActionPhotocopy

  2. #2
    Riso dude 250+ Posts jermyth's Avatar
    Join Date
    Mar 2011
    Location
    Land of Diffusion
    Posts
    427
    Rep Power
    34

    Re: Customer called with RZ990 with error P98-947

    Yeap. That's about as close you can get without getting into the machine.
    Good luck.

  3. #3
    Service Manager 1,000+ Posts
    Customer called with RZ990 with error P98-947


    Join Date
    Aug 2007
    Location
    Brooklyn
    Posts
    1,323
    Rep Power
    48

    Thumbs up Re: Customer called with RZ990 with error P98-947

    Thanks. Are you saying there is a good chance that it's the fuse? Is there something else I should be looking for that is common to this machine with that error code.? Frank

  4. #4
    Riso dude 250+ Posts jermyth's Avatar
    Join Date
    Mar 2011
    Location
    Land of Diffusion
    Posts
    427
    Rep Power
    34

    Re: Customer called with RZ990 with error P98-947

    Something is preventing the 24v, fuse is a first easy guess, but why did the fuse blow? You can't figure that out until you look at the machine and see what is or had happen. If it not the fuse, then did something else blow off the board or boards? I have not had this error in the RZ & EZ units I work on, so I don't have anything more direct for you.
    Good luck.

  5. #5
    Service Manager 1,000+ Posts
    Customer called with RZ990 with error P98-947


    Join Date
    Aug 2007
    Location
    Brooklyn
    Posts
    1,323
    Rep Power
    48

    Thumbs up Re: Customer called with RZ990 with error P98-947

    Thanks Gregory. I will probably see machine Monday or Tuesday, depending on customer. Have a good weekend. Frank

  6. #6
    Field Supervisor 500+ Posts
    Join Date
    Nov 2012
    Posts
    627
    Rep Power
    34

    Re: Customer called with RZ990 with error P98-947

    Fuse F101 used to prevent 24V-A, that power for:
    Elevator motor
    Thermal pressure motor
    Cutter motor
    Read pulse motor
    Print registration pulse motor
    Load pulse motor
    Write pulse motor
    Suction fan
    Master stocker solenoid
    Pressure solenoid
    Print drum lock solenoid
    Paper feed clutch

    If the fuse blow when replaced, you should check electrical equipment in above list
    Good luck!

  7. #7
    Service Manager 1,000+ Posts
    Customer called with RZ990 with error P98-947


    Join Date
    Aug 2007
    Location
    Brooklyn
    Posts
    1,323
    Rep Power
    48

    Thumbs up Re: Customer called with RZ990 with error P98-947

    Thank you Laitang for the information

  8. #8
    Service Manager 1,000+ Posts
    Customer called with RZ990 with error P98-947


    Join Date
    Aug 2007
    Location
    Brooklyn
    Posts
    1,323
    Rep Power
    48

    Thumbs up Re: Customer called with RZ990 with error P98-947

    6.3a fuse for 24v was blown. Replaced and machine gave a message about the standard tray. Noticed preening on Rear elevation plate (024-12207-109). Also flat ribbon cable looked like it took a beating. I believe it is (024-12607-107) .

    Put everything back together to see what would happen after putting rear elevation plate back together as best I could. Now I get T98-129 error. Any help is appreciated while I try to order these parts from someone. Any help is appreciated. Frank

  9. #9
    Service Manager 1,000+ Posts
    Customer called with RZ990 with error P98-947


    Join Date
    Aug 2007
    Location
    Brooklyn
    Posts
    1,323
    Rep Power
    48

    Thumbs up Re: Customer called with RZ990 with error P98-947

    Can someone recommend a company to buy parts from for the rz990. Also does anyone know why i would now be getting the error T98-129 which states in manual " defective scanner gate array pcb(memory check error on the gate array).

    I didn't get this until I reassembled the broken elevation plate R and reinstalled the two sensors on bracket in back of machine which are used for detection when tray is elevated and descending I guess. Frank

  10. #10
    Not a service manager 2,500+ Posts Iowatech's Avatar
    Join Date
    Dec 2009
    Location
    Iowa
    Posts
    3,933
    Rep Power
    97

    Re: Customer called with RZ990 with error P98-947

    Quote Originally Posted by axyun View Post
    Can someone recommend a company to buy parts from for the rz990. Also does anyone know why i would now be getting the error T98-129 which states in manual " defective scanner gate array pcb(memory check error on the gate array).

    I didn't get this until I reassembled the broken elevation plate R and reinstalled the two sensors on bracket in back of machine which are used for detection when tray is elevated and descending I guess. Frank
    For what it is worth, it would be best if you got the parts from Riso. The mothership here tried to get stuff from elsewhere briefly, and failed.
    T9X errors can be mysterious. Sometimes they are caused by the need for updated PCBs or firmware. Other times they are produced by poor quality power supplied by the outlet the machine is plugged into. If you can, look into the later reason first, from what I've seen it is likelier.

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here