http://www.copytechnet.com/forums/ en Fri, 20 Nov 2009 23:42:02 GMT vBulletin 60 http://www.copytechnet.com/forums/images/misc/rss.jpg http://www.copytechnet.com/forums/ http://www.copytechnet.com/forums/sharp/27675-ar-m350n.html Fri, 20 Nov 2009 16:58:32 GMT We have a Sharp AR M350N on top of one of the biggest mountains in WV. :) The machine, mechanically, is fine. We have been having issues with the... We have a Sharp AR M350N on top of one of the biggest mountains in WV. :) The machine, mechanically, is fine. We have been having issues with the machine going into logic loops, or rotating starts, before the machine starts to warm up. Sometimes when the customer uplugs it for a while..... it will come back on. We've changed basicly all the boards, checked voltages, brought it back to our shop for 2 1/2 months with no problem.....we've kinda ran outta ideas....ANYBODY SEEN THIS BEFORE??????????

Patrick ]]> Sharp patwilf http://www.copytechnet.com/forums/sharp/27675-ar-m350n.html http://www.copytechnet.com/forums/sharp/27665-mx-m350n-scan-disabled.html Fri, 20 Nov 2009 13:09:27 GMT Scan software installed and working fine for about 3 months. Customer reports that suddenly they don't receive scanned docs. In the web page under scan settings it says "Error 936 scan is disabled". Machine has scan listed in 22-10 and the product key is in under system settings. I can't find a reference to this error. Has anyone seen this? Thanks. ]]> Sharp RSCA http://www.copytechnet.com/forums/sharp/27665-mx-m350n-scan-disabled.html http://www.copytechnet.com/forums/sharp/27640-ar-161-11x17-paper-bumps.html Thu, 19 Nov 2009 21:35:14 GMT not real sure just how to explan this. when copying 11x17 paper all is fine for the first 5", then there is a small bump in the paper then every 2 5/8" -+ it is repeated down the page right to left always. the copy is not distorted at all. the fuser looks fine. if i copy 11x81/2 paper same thing. if 8 1/2x11R the bumps change to 1" apart and are repeated also. no wrinking of paper is found, as in the pressure roller being bad. ALL BUMPS ARE 1/2 WIDE. I HAVE NOT A CLUE!!! :mad: thanks howard. ]]> Sharp auburn business systems http://www.copytechnet.com/forums/sharp/27640-ar-161-11x17-paper-bumps.html http://www.copytechnet.com/forums/sharp/27624-arm355u-455u-w-o-arp20.html Thu, 19 Nov 2009 16:06:59 GMT Do not have the network print controller ARP20 or 21(?) installed on this machine. Just the standard controller that comes with the U version. Has a... Do not have the network print controller ARP20 or 21(?) installed on this machine. Just the standard controller that comes with the U version. Has a parallel and USB port on the back but when I attempt to connect to these ports they do not show up on my computer running XP. Is there something I am missing or do I have to have the ARP20/21 controller installed to print. And if that is the case how do I update the ROMs on a U version? (I hope you are not going to say the old ARM350 way)!!!!!

Thank you in advance for any information on this subject!

Bil ]]> Sharp bilyahn http://www.copytechnet.com/forums/sharp/27624-arm355u-455u-w-o-arp20.html http://www.copytechnet.com/forums/sharp/27619-sharp-dhcp-settings.html Thu, 19 Nov 2009 14:42:31 GMT I normally avoid this problem by setting the IP address to a static number. When I setup for print with DHCP the unit obtains the address and... I normally avoid this problem by setting the IP address to a static number.

When I setup for print with DHCP the unit obtains the address and setup is prompt with no issues. A period of time will go by and we get a call that they can't print. DHCP has changed the imagers settings to a new number. Setting it back solves the issue. Is there some setting that needs to be changed on Sharps to prevent this from happening? All network settings are Sharp default out of the factory.

Thank you very much for your time and effort in this matter. It has been an annoying matter for Sharps. Don't know if it is for other copiers or not but would like some input if you have it.

Bil ]]> Sharp bilyahn http://www.copytechnet.com/forums/sharp/27619-sharp-dhcp-settings.html http://www.copytechnet.com/forums/sharp/27607-web-setup-arm350n.html Thu, 19 Nov 2009 09:43:07 GMT web setup>Destination Management>it pop up the...]]> Hai all, need help.
I want to delete the networkw scanner address,i open up the Network scanner tool>web setup>Destination Management>it pop up the user name and password box,after i cancel, it show "401 Anthorization Required"
Is my copier or pc need to log in password and how to clear?Any idea?Thanks. ]]> Sharp Peter Sim http://www.copytechnet.com/forums/sharp/27607-web-setup-arm350n.html http://www.copytechnet.com/forums/sharp/27593-sharp-ar-m350n.html Wed, 18 Nov 2009 22:08:12 GMT HY Y have another issue with one ar-m350n, and before beguin to start the reparation y like read your opinion. The problem was, the copier ... HY
Y have another issue with one ar-m350n, and before beguin to start the reparation y like read your opinion.
The problem was, the copier was whithout work about four months, and now y take it for work, but he don`t work, y mean y turn on the power button and the copy donīt do anything???

- y already chek to things: the print board was good, y test in another copier, and another thing that y saw was when y turn on the power, some leds of the main pbw turn on:

some idea, somebody have one this issue like this, or y must beguin change the main pbw??

thanks one time more.. ]]> Sharp DINGO http://www.copytechnet.com/forums/sharp/27593-sharp-ar-m350n.html http://www.copytechnet.com/forums/sharp/27583-mxm620.html Wed, 18 Nov 2009 18:37:32 GMT i've got a problem mxm 620u. it is calling a f2 error.there is no subcode .i've tried toner and dev motors, checked the harness etc.
in sensor check TFSD is high. i removed the sensor from its housing leaving it connected but hanging down so it would not detect toner in the hopper. the sensor was still high.

i have to go with the sensor but could do with some second opinions

thanks

bill ]]> Sharp bonnie750 http://www.copytechnet.com/forums/sharp/27583-mxm620.html http://www.copytechnet.com/forums/sharp/27547-arm-207-u9-81-a.html Wed, 18 Nov 2009 01:33:19 GMT hey have been working on this maching and it keeps coming up with the U9-81 error which in communication error, we have replaced the main board when... hey have been working on this maching and it keeps coming up with the U9-81 error which in communication error, we have replaced the main board when we got the machine in due to a dead display, but since the new main board the display is fine but still the U9 code, any ideas? also i would like to mention that the machine will freeze up after 1 or 2 coppies if it doesnt display the error. im assuming this is related to a bad connection. has currant firmware as well. ]]> Sharp TCS009 http://www.copytechnet.com/forums/sharp/27547-arm-207-u9-81-a.html http://www.copytechnet.com/forums/sharp/27539-sharp-ar-m236.html Tue, 17 Nov 2009 21:35:11 GMT Hy Can somebody help me? Y need the service and parts, manual of a sharp ar-m236. Thanks in advance Hy
Can somebody help me? Y need the service and parts, manual of a sharp ar-m236.

Thanks in advance ]]> Sharp DINGO http://www.copytechnet.com/forums/sharp/27539-sharp-ar-m236.html http://www.copytechnet.com/forums/sharp/27536-arm-550-date-time.html Tue, 17 Nov 2009 19:27:39 GMT Just need a refresher on how to set the date and time for fax system. Thanks everyone Just need a refresher on how to set the date and time for fax system. Thanks everyone ]]> Sharp pontiac http://www.copytechnet.com/forums/sharp/27536-arm-550-date-time.html http://www.copytechnet.com/forums/sharp/27535-mx-m450n-tray-1-misfeeding.html Tue, 17 Nov 2009 18:47:33 GMT I just wanted to share some helpful information if anyone has had this problem out there. Tray 1 was lagging/slow feeding and jamming. All other... I just wanted to share some helpful information if anyone has had this problem out there. Tray 1 was lagging/slow feeding and jamming. All other trays fed correctly. I tried new feed tires, cleaned the shafts, oiled bearings.....and the machine only had 105,000 pages on it. When i went into the simulation to test the clutches they tested fine also.
So I ended up replacing the main drive unit and it fixed the problem. I'm assuming the paper feed clutch was on the verge of going bad. I just thought i'd share some information.:D:D ]]> Sharp patwilf http://www.copytechnet.com/forums/sharp/27535-mx-m450n-tray-1-misfeeding.html http://www.copytechnet.com/forums/sharp/27435-ar-m317.html Mon, 16 Nov 2009 14:59:36 GMT Can anyone tell me the maintenance counts for the AR-m317? drum, developer, trasnsfer unit ect...Also does anyone recomend a good site to pick up the... Can anyone tell me the maintenance counts for the AR-m317? drum, developer, trasnsfer unit ect...Also does anyone recomend a good site to pick up the intrivia manuals for this copier and the 257? Thanks. ]]> Sharp mdavin http://www.copytechnet.com/forums/sharp/27435-ar-m317.html http://www.copytechnet.com/forums/sharp/27407-sharp-ar206.html Mon, 16 Nov 2009 01:14:55 GMT hey im having trouble with a sharp ar 206, it is displaying a jam from the sensor right before the reg roller, i have been messing arround with this... hey im having trouble with a sharp ar 206, it is displaying a jam from the sensor right before the reg roller, i have been messing arround with this machine in our workshop for about 3 days now and it has me scratching my head as to why it is doing this, i have tried replacing the sensor and the sensor arm, but no luck so far,
any imput or ideas would be great ]]> Sharp TCS009 http://www.copytechnet.com/forums/sharp/27407-sharp-ar206.html http://www.copytechnet.com/forums/sharp/27397-mx-2700-fuser-issue.html Sun, 15 Nov 2009 02:09:42 GMT Got a MX-2700 UH Roller that gets full of debris. Cleaned it a few months ago and went back to do some other work to see it coated again, not as bad... Got a MX-2700 UH Roller that gets full of debris. Cleaned it a few months ago and went back to do some other work to see it coated again, not as bad as the first time, but coated just the same.

I thought I saw a Bulletin on this but can't seem to find it. Anyone run into this before? ]]> Sharp CopyGuy2009 http://www.copytechnet.com/forums/sharp/27397-mx-2700-fuser-issue.html