Page 1 of 2 12 LastLast
Results 1 to 10 of 13
  1. #1
    Service Manager 1,000+ Posts
    Join Date
    Sep 2012
    Posts
    1,129
    Rep Power
    39

    Bizhub 227 fax result "Reset Modes"

    I have seen on this model when sending a fax. Some show "Job Complete" as normal but some show as "Reset Modes" I have confirmed the fax has worked successfully.

    I am curious to what this means. I have found nothing in any documentation and when I was on a support call with KMBS for some fax issues they didn't know either.

    Only asking because Im curious.
    Last edited by wseyller; 10-07-2015 at 11:22 PM.

  2. #2
    RTFM!! 5,000+ Posts allan's Avatar
    Join Date
    Apr 2010
    Location
    Centurion
    Posts
    5,387
    Rep Power
    152

    Re: Bizhub 227 fax result "Reset Modes"

    Reset (initialize) the fax?
    Whatever

  3. #3
    Service Manager 1,000+ Posts
    Join Date
    Sep 2012
    Posts
    1,129
    Rep Power
    39

    Re: Bizhub 227 fax result "Reset Modes"

    Yep. Actually originally there was some issues with faxing at medical office. They have analog line from at&t. There was a lot of NG results. KMBS support had me make several changes for voip issues and so far seems to help over 24 hours. I sent a fax to KMBS and it showed "reset modes".

    Also my office wanted to replace the fax board just in case which I did today. I initialize and I notice the settings in service and admin mode look strange. Then I notice no dial tone when using off hook. I initialized again and now the default settings look correct and I do now get a dial tone. I then applied the settings from KMBS and tested a few. One to my office shows the "reset modes". It seems almost half of them do this but there is no problem so I told customer not to worry about it.



    Sent from my XT1254 using Tapatalk

  4. #4
    RTFM!! 5,000+ Posts allan's Avatar
    Join Date
    Apr 2010
    Location
    Centurion
    Posts
    5,387
    Rep Power
    152

    Re: Bizhub 227 fax result "Reset Modes"

    Could be screwed up firmware. Or non-volatile data.
    Whatever

  5. #5
    Aging Tech 10,000+ Posts
    Bizhub 227 fax result "Reset Modes"

    copier addict's Avatar
    Join Date
    Jul 2013
    Location
    Diamond
    Posts
    11,916
    Rep Power
    322

    Re: Bizhub 227 fax result "Reset Modes"

    Sounds like it could be ECM. Try turning it off and see if you still get that message.

  6. #6
    Field Supervisor 2,500+ Posts
    Join Date
    Jun 2009
    Posts
    3,009
    Rep Power
    96

    Re: Bizhub 227 fax result "Reset Modes"

    We have found that the fax on the new 7 and 8 series must be initialized twice during setup with a power cycle between the initials...once this is accomplished you can configure the defaults and marketing area. Emujo
    If you don't see your question answered in the forum, please don't think it's OK to PM me for a personal reply...I do not give out firmware and/or manuals.

  7. #7
    Service Manager 1,000+ Posts
    Join Date
    Sep 2012
    Posts
    1,129
    Rep Power
    39

    Re: Bizhub 227 fax result "Reset Modes"

    Thanks emujo. I think I'm starting to see the same pattern.

    The after first initialize of the new kit ecm was already off. After second initialize ecm was back on as default. In admin/fax settings number of rings was set to zero but after 2nd initialize it was now at 2 rings as it should. There are several other settings that were wrong.

    Sent from my XT1254 using Tapatalk

  8. #8
    Junior Member
    Join Date
    Feb 2020
    Location
    WA
    Posts
    2
    Rep Power
    0

    Re: Bizhub 227 fax result "Reset Modes"

    You need to turn off blank page removal from application, it should bring back job complete resault.

  9. #9
    Service Manager 10,000+ Posts
    Bizhub 227 fax result "Reset Modes"

    Phil B.'s Avatar
    Join Date
    Jul 2016
    Location
    Raleigh NC
    Posts
    22,656
    Rep Power
    658

    Re: Bizhub 227 fax result "Reset Modes"

    Quote Originally Posted by aungsithu View Post
    You need to turn off blank page removal from application, it should bring back job complete resault.
    Hey Grave Robber....

    this thread has been DEAD for 5 YEARS!

  10. #10
    Junior Member
    Join Date
    Apr 2022
    Location
    Down Under
    Posts
    1
    Rep Power
    0

    Re: Bizhub 227 fax result "Reset Modes"

    Quote Originally Posted by Phil B. View Post
    Hey Grave Robber....

    this thread has been DEAD for 5 YEARS!
    Thank you Grave Robber. This reply after 5 years just saved me alot of time trying to figure this out.
    Also who still use fax in 2022 btw.

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here