Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Page 1 of 2 12 LastLast
Results 1 to 10 of 13
  1. #1
    matty 2008
    Guest

    BizHub C 250 - Transfer Unit

    My Bizhub constantly displays the message; Replace Transfer Unit. Is there any way to get additional life out of this without buying the whold transfer unit kit. The cheapest I can find it is about $300 US.

  2. #2
    DarthAlbin
    Guest
    I would prefer you pay for the transfer belt and transfer roller. You run the risk of damaging the belt and your machine (not to mention putting your safety at risk) if service isn't performed by a qualified technician. Also, you may suffer poor image quality soon after the "repair" as a result.

    But... one might be able to replace a fuse in the belt assembly with a fuse of the same rating to get by. Do this only once. Next time buy the belt/kit.

  3. #3
    Technician
    Join Date
    Jul 2008
    Posts
    29
    Rep Power
    22

    c250

    To reset it you must replace an 80ma fuse. The process is as follows:

    1. Pull the transfer belt out.
    2. Remove the bar that has the stripper finger on it. (2 screws, 1 on top and
    1 on the front.)
    3. Remove the ground spring from the shaft.
    4. Remove the clip and then remove the metal handle.
    5. Remove the small black screw. The cover will then come off and you will
    see the fuse. Put the new fuse in and the belt will reset.

  4. #4
    DarthAlbin
    Guest
    Also, be very careful not to touch the surface of the belt. prevent anything from scratching it.

  5. #5
    Conservative in Exile 250+ Posts laserman06's Avatar
    Join Date
    Dec 2007
    Location
    Hebron, KY
    Posts
    323
    Rep Power
    26
    Quote Originally Posted by DarthAlbin View Post
    I would prefer you pay for the transfer belt and transfer roller. You run the risk of damaging the belt and your machine (not to mention putting your safety at risk) if service isn't performed by a qualified technician. Also, you may suffer poor image quality soon after the "repair" as a result.

    But... one might be able to replace a fuse in the belt assembly with a fuse of the same rating to get by. Do this only once. Next time buy the belt/kit.
    You must work for Konica. Actually had one that made it through 2 full cycles and half of a third.
    The family that prays together, stays together!
    Smile God created you and He doesn't make mistakes!

    Relax, God IS in control!

    Be still and know that I am God
    Ps 46:10

  6. #6
    Senior Tech 250+ Posts
    BizHub C 250 - Transfer Unit

    DadO's Avatar
    Join Date
    Dec 2007
    Location
    Curently:" In Copier horror dream"
    Posts
    396
    Rep Power
    26
    Suspicious at all

  7. #7
    Junior Member
    Join Date
    Jan 2019
    Posts
    3
    Rep Power
    0

    Re: BizHub C 250 - Transfer Unit

    Hello everyone and thank you to those who can help me.

    I have a bizhub 250, it indicates the lack of change of the transfer unit, I change the fuse 80 ma of the transfer unit and I always have the message that appears, it does not want reset.

    I also change IU STOP SETTING by NO STOP but the machine and still blocked and ask me to change the transfer unit.
    I also reset all the counters.

    So how do I reset the transfer unit? Where can the problem come from?

  8. #8
    Senior Tech 100+ Posts avecosat's Avatar
    Join Date
    Jun 2012
    Posts
    105
    Rep Power
    15

    Re: BizHub C 250 - Transfer Unit

    Is the only way , be sure the fuse is 80mA .

  9. #9
    Service Manager 1,000+ Posts
    BizHub C 250 - Transfer Unit


    Join Date
    Sep 2005
    Location
    South Jersey
    Posts
    1,499
    Rep Power
    49

    Re: BizHub C 250 - Transfer Unit

    80ma "fast blow" fuse

  10. #10
    Aging Tech 1,000+ Posts
    BizHub C 250 - Transfer Unit

    copier addict's Avatar
    Join Date
    Jul 2013
    Location
    Desboro
    Posts
    1,893
    Rep Power
    45

    Re: BizHub C 250 - Transfer Unit

    Quote Originally Posted by optsun View Post
    Hello everyone and thank you to those who can help me.

    I have a bizhub 250, it indicates the lack of change of the transfer unit, I change the fuse 80 ma of the transfer unit and I always have the message that appears, it does not want reset.

    I also change IU STOP SETTING by NO STOP but the machine and still blocked and ask me to change the transfer unit.
    I also reset all the counters.

    So how do I reset the transfer unit? Where can the problem come from?
    If you have any P codes being displayed I believe the belt will not reset.

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •