If i order a new one which part number am i supposed to order?On infohub it lists 2 cards in the same slot based on your firmware?
Since i dont know what firmware was on it does it matter?God what a bothersome issue
If i order a new one which part number am i supposed to order?On infohub it lists 2 cards in the same slot based on your firmware?
Since i dont know what firmware was on it does it matter?God what a bothersome issue
I don't like the new copier I just bought. It says "put face down" but every time I do it, it blinds my eyes.
the BH601 uses a usb stick to update FW.
when ordering a new one, the only difference between the two is for what model you have. 601 or 751. Unfortunately, I just checked my parts catalogue and it doesnt specify (the older parts lists said whether it was for a 601 or 751).. my guess would be that its the A0PNR72211 part. you can also go to the konica web site and go to the service dropdown and select "one stop product support". in there you can select your model and find the 601 recovery.exe in the firmware section. then follow these instructions (they are also in the same section)
Release notes for the Bizhub 601 CF card recovery firmwareThis firmware, Recovery601.exe is for the recovery of a corrupted CF card. The recoveryfirmware should only be used after flashing the machine via the USB drive port has beendone and the firmware on the CF card is suspected to be corrupted.To perform the recovery procedure, remove the CF card from the machine and install it ina CF card reader/writer to access the files on the CF card. Select the CF card, NOTE: DONOT FORMAT THE CF CARD AS IT WILL NO LONGER BE RECOGNIZED BYTHE MACHINE. Create two new folders, one to backup the current files and one tounzip the new files into. Select all files on the CF card and cut and paste them to one ofthe newly created folders. Next, unzip the recovery firmware into the other new folderthat was created then, select all and cut and paste them to the CF card. When the files aredone transferring, make sure to properly eject the CF card before removing it.Reinstall the CF card into the machine and turn it on. The firmware level will now be atthe first release version for the machine. The machine can now be flashed up to the latestfirmware level using a USB drive.
I don't like the new copier I just bought. It says "put face down" but every time I do it, it blinds my eyes.
Corruption of the CF card.
SOLUTION: Delete the files from the CF card and write the version 10.0 Base files directly to the card. Only delete the files from the CF card and copy the new files from the Base firmware download to it. This will recover the machine.
IMPORTANT: Change the administrator password before upgrading firmware beyond the base level. To do this, perform the following:
1. Enter Service Mode.
2. Press Stop, 0, Clear on the 10-key pad of the control panel.
3. Touch Administrator Password.
4. Enter the administrator password.
5. Touch End.
From this point, flash the machine as normal to the latest firmware version. The latest version firmware or system software is available via the Konica Minolta Download Selector or One-Stop Product Support.
If the problem is not resolved, please replace the CF card (p/n A0PN R722 11) which is compatible with version 20 firmware.
WARNING:DO NOT FORMAT THE CF CARD as this will render the card unreadable.
Release notes for the Bizhub 601
CF card recovery firmware
This firmware, Recovery601.exe is for the reco
very of a corrupted CF card. The recovery
firmware should only be used after flashing
the machine via the USB drive port has been
done and the firmware on the CF card is suspected to be corrupted.
To perform the recovery procedure, remove th
e CF card from the machine and install it in
a CF card reader/writer to
access the files on the CF
card. Select the CF card,
NOTE: DO
NOT FORMAT THE CF CARD AS IT WILL NO LONGER BE RECOGNIZED BY
THE MACHINE. Create two new folders, one to b
ackup the current files and one to
unzip the new files into. Select all files on th
e CF card and cut and paste them to one of
the newly created folders. Next, unzip the recovery firmware into the other new folder
that was created then, select all and cut and
paste them to the CF card. When the files are
done transferring, make sure to properly
eject the CF card before removing it.
Reinstall the CF card into the machine and tu
rn it on. The firmware level will now be at
the first release version for the machine. The
machine can now be flashed up to the latest
firmware level using a USB drive.
check your PMs
i have the file.. i am having trouble uploading it as an attachment
its 50+meg thats why.
i already gave it to him.
Bookmarks