Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 4 of 4

Thread: BHC353 C-2253

  1. #1
    Service Manager 1,000+ Posts
    BHC353 C-2253

    Desert Rat's Avatar
    Join Date
    May 2008
    Location
    Valley of the Sun
    Posts
    1,089
    Rep Power
    44

    BHC353 C-2253

    Seemed straight forward. Rubber came off the one or the fuser rollers. Get another unit and install it.
    The machine printed out everything in the print que. I noticed streaks and traced it to the transfer belt.
    Took it out and saw the streaks so I cleaned it with 99% pure alcohol. So far so good.
    Cleaned out the cleaning unit and found a couple of pieces of rubber. Wiped the blade off powered both belt and blade
    with toner and put it back in and got the code C2253.

    C2253: Color PC motor’s failure to turn

    I must be stressed because I jumped to the conclusion that rubber might be stuck in the gears.
    But hind sight tells me it would have had to go through the back mech plate.
    I'll bet I didn't powder the belt and blade enough. I'll check this tomorrow.
    Mean while how much trouble is it to pull the motor M2 PC drive motor?

    I've just re-read the manual for taking out the belt, I usually pull the drums out about an inch or so for
    clearance. But it looks like I did it right. Also read where the color drums are driven by a different motor
    than the transfer belt.
    Is there something I've overlooked? Please let me know.

    I do not know when this machine was discontinued so I'm not sure if it will be worth it to fix it.

    Thanks

    DR

  2. #2
    Former KM Senior Tech 500+ Posts srvctec's Avatar
    Join Date
    Oct 2009
    Location
    Central Kansas
    Posts
    827
    Rep Power
    63

    Re: BHC353 C-2253

    On end of life list June 2017. Not sure how difficult it would be to get to the motor as I've not had to mess with that one yet although I've changed out numerous main motors.

    I used to slightly slide out he IUs whenever removing the belt but stopped that years ago when I noticed it doesn't make any difference for clearance. Sounds like you're on the right track since the code wasn't there prior to the fuser failure.
    Started in the copier service business in the fall of 1988 and worked at the same company for 33.5 years, becoming the senior tech in 2004 but left to pursue another career on 4/29/22.

  3. #3
    Service Manager 1,000+ Posts
    Join Date
    Apr 2009
    Location
    LaPorte Indiana
    Posts
    1,054
    Rep Power
    43

    Re: BHC353 C-2253

    Can you manually spin the IU's ?? Then re-seat try again.

  4. #4
    Service Manager 1,000+ Posts
    BHC353 C-2253

    Desert Rat's Avatar
    Join Date
    May 2008
    Location
    Valley of the Sun
    Posts
    1,089
    Rep Power
    44

    Re: BHC353 C-2253

    mo0651 & srvctec,

    Thank you for your suggestions. As it turned out the yellow drum unit was bound up
    probably due to a piece of rubber from the fuser. I replaced that and check the machine.
    The drum drive turned OK but the developer drive was very very stiff. Had to use trouble reset
    to get it to come back to life. After that,
    iIt ran OK, but the transfer belt cleaning did not fix the smears it had to be replaced.
    After that, everything fell back into place.

    Thanks again

    DR
    Last edited by Desert Rat; 11-22-2017 at 04:21 PM. Reason: clarityt

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here