Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 27
  1. #11
    Field Supervisor 500+ Posts
    Join Date
    Mar 2011
    Location
    Gothenburg
    Posts
    803
    Rep Power
    27

    Re: C258 won't boot / stuck at 2 bars

    So my collegue tried the MFP board repair procedure. Booting the recovery tool -> no change -> booting with s-ata FW -> machine finally boot up into the update but says "FW already up to date". Then he did again installed the new eMMC board while leaving the HDD disconnected and then the machine worked. He was shure that he tried that before so it's unclear how this procedure did the magic. After re-installing the HDD the adress book was also back on track.

    I'll keep the new MFP board in stock in case this is just a temporary success.

  2. #12
    Technician
    Join Date
    Dec 2016
    Posts
    24
    Rep Power
    5

    Re: C258 won't boot / stuck at 2 bars

    Can I share a789be.tar reset firmware?
    I also have machine can not boot, please

  3. #13
    Technician
    Join Date
    Dec 2016
    Posts
    24
    Rep Power
    5

    Re: C258 won't boot / stuck at 2 bars

    We've tried booting with MFP reset toll (that tiny 10kb *.tar file) - no change of behaviour unfortunately


    Can I share firmware?
    Last edited by gtr5320; 03-14-2018 at 08:49 AM.

  4. #14
    Junior Member
    Join Date
    Aug 2015
    Posts
    6
    Rep Power
    0

    Re: C258 won't boot / stuck at 2 bars

    I had a C654 hang on 2 bars. I removed all accessories, finisher, ADF, all usb connections. See if it turns on. If it does, add one accessory at a time until you hang again. Or in my case just reseating the ADF pin connector fixed my issue.

  5. #15
    Technician
    Join Date
    Dec 2016
    Posts
    24
    Rep Power
    5

    Re: C258 won't boot / stuck at 2 bars

    Thank you but it is invalid , , Firmware allows me to try it?

  6. #16
    Junior Member
    Join Date
    Nov 2016
    Location
    enfield
    Posts
    7
    Rep Power
    0

    Re: C258 won't boot / stuck at 2 bars

    Quote Originally Posted by Gift View Post
    So my collegue tried the MFP board repair procedure. Booting the recovery tool -> no change -> booting with s-ata FW -> machine finally boot up into the update but says "FW already up to date". Then he did again installed the new eMMC board while leaving the HDD disconnected and then the machine worked. He was shure that he tried that before so it's unclear how this procedure did the magic. After re-installing the HDD the adress book was also back on track.

    I'll keep the new MFP board in stock in case this is just a temporary success.
    hi can i ask how you got another emmc board i have one thats down as well how did you order one
    regards
    steve r

  7. #17
    Technician
    Join Date
    Dec 2016
    Posts
    24
    Rep Power
    5

    Re: C258 won't boot / stuck at 2 bars

    Press "Stop" to boot A789be.tar No response, is there a problem (a789be.tar can also be used in 287?

  8. #18
    Field Supervisor 500+ Posts copytechman's Avatar
    Join Date
    Nov 2008
    Location
    Barrie, Ontario
    Posts
    790
    Rep Power
    28

    Re: C258 won't boot / stuck at 2 bars

    Where does one find the reset tool on KM's tech side website? I can't seem to locate it anywhere? I've looked under special and regular firmware? Any guidance would be appreciated.

    Thanks!

    A.

  9. #19
    Field Supervisor 500+ Posts copytechman's Avatar
    Join Date
    Nov 2008
    Location
    Barrie, Ontario
    Posts
    790
    Rep Power
    28

    Re: C258 won't boot / stuck at 2 bars

    No one knows?

    A.

  10. #20
    Technician
    Join Date
    Dec 2016
    Posts
    24
    Rep Power
    5

    Re: C258 won't boot / stuck at 2 bars

    Can you answer? Thank you very much.

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •