Likes Likes:  0
Dislikes Dislikes:  0
Page 1 of 2 12 LastLast
Results 1 to 10 of 11
  1. #1
    Trusted Tech 50+ Posts
    Join Date
    Dec 2015
    Location
    Erie,PA
    Posts
    91
    Rep Power
    7

    C6000 with punch reg problem

    Hi Guys,

    I have a C6000 with FS-612 and a PK-512 in it. The problem that I am having is that the punch registration is off. Running 5 prints, the punch is in different places. I have replaced the entrance rollers of the finisher and have adjusted the paper edge sensor. Just wondering if there is some solution for this. When I was changing the top roller the belt was a little loose. Could not see if there was and idler to tighten.

    Thanks
    KEN
    Attached Images Attached Images

  2. #2
    Master Of The Obvious 10,000+ Posts
    C6000 with punch reg problem

    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    16,603
    Rep Power
    275

    Re: C6000 with punch reg problem

    Have you cleaned the punch paper size sensors? When they get dirty enough it will punch all over the place, and give you J7216 jams. I had a school that was using paper that was so dusty that I was cleaning these sensors on 4 day intervals. For those machines I MacGuyvered a shutter type of sensor cleaner of a sort. When the punch holes started wandering, the enduser would open the finisher door and pull out the cleaner mechanism. It was spring loaded to pop back in. I was pretty happy overall with that setup. =^..^=
    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.
    3) if you're going to ask about jams include the jam code.
    4) if you're going to ask about an error code include the error code.


    blackcat: Master Of The Obvious =^..^=

  3. #3
    Trusted Tech 50+ Posts
    Join Date
    Dec 2015
    Location
    Erie,PA
    Posts
    91
    Rep Power
    7

    Re: C6000 with punch reg problem

    I did have the punch unit out. Guess that I will take it out again and blow it out!!!

    Thanks
    KEN

  4. #4
    Master Of The Obvious 10,000+ Posts
    C6000 with punch reg problem

    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    16,603
    Rep Power
    275

    Re: C6000 with punch reg problem

    I thought for sure that I attached a photo yesterday:

    PK-522 senor cleaning shutter.JPGFS532 punch paper size sensors1.JPG
    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.
    3) if you're going to ask about jams include the jam code.
    4) if you're going to ask about an error code include the error code.


    blackcat: Master Of The Obvious =^..^=

  5. #5
    Trusted Tech 50+ Posts
    Join Date
    Dec 2015
    Location
    Erie,PA
    Posts
    91
    Rep Power
    7

    Re: C6000 with punch reg problem

    Thanks, I did not know those were there. I had to look it up to see where those were. I will take a look at those on Monday, I hope.

  6. #6
    Trusted Tech 50+ Posts
    Join Date
    Dec 2015
    Location
    Erie,PA
    Posts
    91
    Rep Power
    7

    Re: C6000 with punch reg problem

    Okay, I checked the sensors and it still did this. I cleaned the foil patches on the guide. I contacted KM and they said to change the sensor board and if that does not work to replace the FNS Driver board. Well I did do that with no improvement. I go into the adjust on the screen and the punch, the horizontal for the machine is at +50 and that is as far as it goes. I go to the -50 and it misses the paper. I am about to update my request on the KM site. Any suggestions before I get a around the bush answer from KM.

    Thanks
    KEN

  7. #7
    Trusted Tech 50+ Posts
    Join Date
    Dec 2015
    Location
    Erie,PA
    Posts
    91
    Rep Power
    7

    Re: C6000 with punch reg problem

    Oh, PS. They have a C452 and did a punch job on it and the holes line up real nice.....

  8. #8
    Service Manager 1,000+ Posts
    C6000 with punch reg problem

    Synthohol's Avatar
    Join Date
    Mar 2016
    Location
    north jersey
    Posts
    1,762
    Rep Power
    34

    Re: C6000 with punch reg problem

    what do you notice when you are jigging the door and watching the behavior of the paper?
    short or excessive loop forming?
    whats the punch count?

  9. #9
    Trusted Tech 50+ Posts
    Join Date
    Dec 2015
    Location
    Erie,PA
    Posts
    91
    Rep Power
    7

    Re: C6000 with punch reg problem

    Check on the punch count of the management list and there is only 5220 on the punch. The copier has 1.6 million. This machine is counting 2 for 11x17. KM says to make sure the firmware is at 60 and to recall standard data and do punch alignments.

    KEN

  10. #10
    Trusted Tech 50+ Posts
    Join Date
    Jul 2017
    Location
    Montvale
    Posts
    50
    Rep Power
    3

    Re: C6000 with punch reg problem

    You mentioned the drive belt was loose, have you been able to tighten the tension for the belt?, maybe its as simple as that.

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •