Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Page 1 of 2 12 LastLast
Results 1 to 10 of 11
  1. #1
    Master Of The Obvious 10,000+ Posts
    bizhub 808 with scanning issue

    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    22,444
    Rep Power
    462

    bizhub 808 with scanning issue

    Scans from the glass start scanning 32mm from the index plate. Leading edge is adjustable, but nowhere near that far.

    Scans through the DF come out charcoal gray or black, because light source #1 is parked under the edge of the shading plate. Read position can be adjusted, just nowhere near enough to reach the correct scan position.

    There are four occurrences of C9401, mainly because light source #1 was not properly aligned with the white plate at the time the shading adjustment was attempted.

    The scanner finds home position each time after scanning, but then pulses out from that HP sensor too far. The scanner has not crashed yet, but I haven't tried scanning an 18" long original.

    We've swapped the scanner home position sensor with an identical sensor from the same machine, and it does change state properly in test mode.
    The scanner moves smoothly, lubricated rails, cables properly tensioned. Replaced scanner motor. Tried various timing belt tensions, no change. It's currently got the original belt tensioning spring.
    Replaced scanner control board. Replaced MFP board. Updated firmware to G00-U8. Clipped wire ties in the scanner area.

    For me, the really weird thing is that occasionally it will scan one document perfectly aligned.

    Am I missing something obvious? =^..^=
    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.
    3) if you're going to ask about jams include the jam code.
    4) if you're going to ask about an error code include the error code.
    5) You are the person onsite. Only you can make observations.

    blackcat: Master Of The Obvious =^..^=

  2. #2
    Service Manager 5,000+ Posts tsbservice's Avatar
    Join Date
    May 2007
    Posts
    7,102
    Rep Power
    346

    Re: bizhub 808 with scanning issue

    I would start reading theory of operation for that machine again. Seems you covered almost every avenue, so it could be something very simple. C9401 on 654/754e was CCD, but your issue is different.
    A tree is known by its fruit, a man by his deeds. A good deed is never lost, he who sows courtesy, reaps friendship, and he who plants kindness gathers love.

    Blessed are they who can laugh at themselves, for they shall never cease to be amused.

    I don't reply to private messages from end users.

  3. #3
    Senior Tech 250+ Posts driving lots of miles's Avatar
    Join Date
    Jun 2016
    Location
    Kansas
    Posts
    362
    Rep Power
    22

    Re: bizhub 808 with scanning issue

    I am probably off base but has someone changed paper size/ scan settings? You seem to have covered everything else.

  4. #4
    Master Of The Obvious 10,000+ Posts
    bizhub 808 with scanning issue

    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    22,444
    Rep Power
    462

    Re: bizhub 808 with scanning issue

    Quote Originally Posted by driving lots of miles View Post
    I am probably off base but has someone changed paper size/ scan settings? You seem to have covered everything else.
    Explain. =^..^=
    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.
    3) if you're going to ask about jams include the jam code.
    4) if you're going to ask about an error code include the error code.
    5) You are the person onsite. Only you can make observations.

    blackcat: Master Of The Obvious =^..^=

  5. #5
    Field Supervisor 500+ Posts Woxner's Avatar
    Join Date
    Jul 2011
    Location
    Felixstowe England
    Posts
    780
    Rep Power
    41

    Re: bizhub 808 with scanning issue

    make sure the machine type is correct according to resolution. here is something else too


    Check and clean the CCD sensor. Check and reseat connector CN3 on the CCD board (CCDB). Next, check the CCD cable and wiring for damage or loose connections. Reconnect or repair as needed. Test MFP operation. If any issue is found. Replace the CCD unit.
    CAUTION: When the CCD is replaced, perform the following adjustments.

    [Service Mode] -> [System 2] -> [CCD Calibration] = [OFF]

    [Service Mode] -> [System 2] -> [
    Line Mag Setting] = [OFF]

    [Service Mode] -> [Machine] -> [Scan Area] -> [Main Scan Zoom Adj.]


    Note: If the specifications are not met, loosen the CCD board mounting screws and move the CCD board in the sub scan direction as necessary. Hold the CCD board by hand when moving it. NEVER use a screwdriver or similar tool to tap to move it, as a varied distance between the CCD sensor and lens results.

    [Service Mode] -> [Machine] -> [Scan Area] -> [Scanner Image Side Edge]

    [Service Mode] -> [Machine] -> [Printer Area] -> [Image Position: Leading Edge]
    If error persists, continue troubleshooting.

    Please refer to Board locations, connectors and wiring.

    IMPORTANT: Please check the wiring harness(es) by unplugging all associated connectors, checking all wires to ground (for a short) and checking continuity of the wiring (for an open).

  6. #6
    Master Of The Obvious 10,000+ Posts
    bizhub 808 with scanning issue

    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    22,444
    Rep Power
    462

    Re: bizhub 808 with scanning issue

    Well the CCD is about the last thing left in the scanner not changed. I have a hard time seeing how it would affect light source#1 position though.

    All the scanner connectors have been examined and reseated multiple times. Thanks for your response. =^..^=
    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.
    3) if you're going to ask about jams include the jam code.
    4) if you're going to ask about an error code include the error code.
    5) You are the person onsite. Only you can make observations.

    blackcat: Master Of The Obvious =^..^=

  7. #7
    Senior Tech 250+ Posts driving lots of miles's Avatar
    Join Date
    Jun 2016
    Location
    Kansas
    Posts
    362
    Rep Power
    22

    Re: bizhub 808 with scanning issue

    Quote Originally Posted by blackcat4866 View Post
    Explain. =^..^=
    I was thinking that if settings had been changed it could be throwing off the position of the scanner. We had a copier that was not copying the entire page or parts of it and the page and tray paper settings had been changed. The internal prints were coming out perfect, it was just the scans and copies.

  8. #8
    Master Of The Obvious 10,000+ Posts
    bizhub 808 with scanning issue

    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    22,444
    Rep Power
    462

    Re: bizhub 808 with scanning issue

    Quote Originally Posted by driving lots of miles View Post
    I was thinking that if settings had been changed it could be throwing off the position of the scanner. We had a copier that was not copying the entire page or parts of it and the page and tray paper settings had been changed. The internal prints were coming out perfect, it was just the scans and copies.
    I'm not ready to discount your idea yet, but what sort of setting might the customer change that would affect the light source #1 scan position under the slit glass? =^..^=
    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.
    3) if you're going to ask about jams include the jam code.
    4) if you're going to ask about an error code include the error code.
    5) You are the person onsite. Only you can make observations.

    blackcat: Master Of The Obvious =^..^=

  9. #9
    Senior Tech 250+ Posts driving lots of miles's Avatar
    Join Date
    Jun 2016
    Location
    Kansas
    Posts
    362
    Rep Power
    22

    Re: bizhub 808 with scanning issue

    Quote Originally Posted by blackcat4866 View Post
    I'm not ready to discount your idea yet, but what sort of setting might the customer change that would affect the light source #1 scan position under the slit glass? =^..^=
    There should not be anything the customer could do that would affect the light source, this is a really an odd problem.

  10. #10
    Master Of The Obvious 10,000+ Posts
    bizhub 808 with scanning issue

    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    22,444
    Rep Power
    462

    Re: bizhub 808 with scanning issue

    Correction: I just got this from the team leader: The second new CCD fixed it. The first new CCD did not change the symptoms. =^..^=
    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.
    3) if you're going to ask about jams include the jam code.
    4) if you're going to ask about an error code include the error code.
    5) You are the person onsite. Only you can make observations.

    blackcat: Master Of The Obvious =^..^=

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here