Thanks Thanks:  0
Dislikes Dislikes:  0
Results 1 to 10 of 10
  1. #1
    Service Manager 1,000+ Posts
    Bizhub C360 "No animation " message aand not copying or printing


    Join Date
    Aug 2007
    Location
    Brooklyn
    Posts
    1,277
    Rep Power
    36

    Thumbs up Bizhub C360 "No animation " message aand not copying or printing

    a message "No animation guide data available. Contact your administrator."

    I understand that that refers to the movie data used to show customer hot to remove jams and such. I would not care but machine evidently had a second problem and I don't if it occurred after customer tried going into admistrative settings. The machine won't pring or make copies but will scan the documents from glass or adf. Job goes into que and I noticed that under "status" fo job it says "stopprint". When customer tries to print from computer it says machine is offline.

    I would not think that the "no animation guide" message would effect printing and copying. Please advise . Your help is welcome and appreciated very much. Frank

  2. #2
    Aging Tech 1,000+ Posts
    Bizhub C360 "No animation " message aand not copying or printing


    Join Date
    Jul 2013
    Location
    Desboro
    Posts
    1,755
    Rep Power
    43

    Re: Bizhub C360 "No animation " message aand not copying or printing

    Most of the time this issue is because one of the consumables, drum, dev etc. is at end of life. Either install PPLM firmware and adjust soft switches and memory switches or replace consumable that is at EOL.

  3. #3
    Service Manager 1,000+ Posts
    Bizhub C360 "No animation " message aand not copying or printing


    Join Date
    Aug 2007
    Location
    Brooklyn
    Posts
    1,277
    Rep Power
    36

    Thumbs up Re: Bizhub C360 "No animation " message aand not copying or printing

    Rhank you Copier Addict. i did not see any message to change anything. Also why would computer say machine is offline when customer tries

    to print. I would think it would say something needs to be changed instead of machine is offline. Frank

  4. #4
    Service Manager 1,000+ Posts
    Bizhub C360 "No animation " message aand not copying or printing


    Join Date
    Feb 2010
    Posts
    1,288
    Rep Power
    39

    Re: Bizhub C360 "No animation " message aand not copying or printing

    You probably don't see any message to replace consumables because the End of Life has been disabled but it sounds like the "Stop or No Stop" is still set to "Stop". It's somewhere in the service mode but I don't remember where.

  5. #5
    Field Supervisor 500+ Posts
    Bizhub C360 "No animation " message aand not copying or printing


    Join Date
    Sep 2011
    Location
    Perth, Western Australia
    Posts
    563
    Rep Power
    21

    Re: Bizhub C360 "No animation " message aand not copying or printing

    Wish the 8 series drums went this long lol

  6. #6
    Senior Tech 100+ Posts
    Join Date
    Oct 2009
    Posts
    190
    Rep Power
    20

    Re: Bizhub C360 "No animation " message aand not copying or printing

    Quote Originally Posted by JR2ALTA View Post
    You probably don't see any message to replace consumables because the End of Life has been disabled but it sounds like the "Stop or No Stop" is still set to "Stop". It's somewhere in the service mode but I don't remember where.
    The Firmware on the machine must be at a particular level to achieve some of the soft switch settings that control End of Life. If the F/W is not up to speed, certain soft switches will not appear in the Service Mode, and therefore not allow you to make the changes necessary.

    I had a C-360 do this a couple of weeks ago and although we thought we had set the end of life settings correctly, one of them was missing and the machine shut down and said "waiting to print" or something like that. Loaded the latest F/W, went back in to set everything per the bulletin and VOILA, started spitting out pages again!
    OC

  7. #7
    Super Tech 500+ Posts CompyTech's Avatar
    Join Date
    Feb 2011
    Location
    MS
    Posts
    648
    Rep Power
    24

    Re: Bizhub C360 "No animation " message aand not copying or printing

    Quote Originally Posted by JR2ALTA View Post
    You probably don't see any message to replace consumables because the End of Life has been disabled but it sounds like the "Stop or No Stop" is still set to "Stop". It's somewhere in the service mode but I don't remember where.
    I Believe it's Stop, 0 , Clear. Then go under Stop Life Settings(appears on right side of screen).

  8. #8
    Super Tech 500+ Posts CompyTech's Avatar
    Join Date
    Feb 2011
    Location
    MS
    Posts
    648
    Rep Power
    24

    Re: Bizhub C360 "No animation " message aand not copying or printing

    Quote Originally Posted by rrrohan View Post
    Wish the 8 series drums went this long lol
    Ha no kidding I knew once they switched to charge rollers that they wouldn't last that long. Had many go out on the Kyoceras but many of them allowed you to change just the charger separately.

  9. #9
    Senior Tech 100+ Posts
    Join Date
    Mar 2017
    Posts
    207
    Rep Power
    10

    Re: Bizhub C360 "No animation " message aand not copying or printing

    Quote Originally Posted by axyun View Post
    Rhank you Copier Addict. i did not see any message to change anything. Also why would computer say machine is offline when customer tries

    to print. I would think it would say something needs to be changed instead of machine is offline. Frank
    Stopprint indicates that a consumable is at the end of life and the MFP will not produce another copy until it's replaced, reset, or as one of the posters added, the PPLM settings are enabled. The print driver is receiving these same messages via SNMP so it knows that the MFP can't print either. You may be able to just reset the counter for what ever item is at EOL, but this can cause some CQ issues. Additionally, some of these items required a fuse to blow to indicated a new replacement. I think even the PPLM mods would not prevent eventual stoppage with things like the x-fer belt and the fuser. E

  10. #10
    Master Of The Obvious 10,000+ Posts
    Bizhub C360 "No animation " message aand not copying or printing

    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    16,603
    Rep Power
    275

    Re: Bizhub C360 "No animation " message aand not copying or printing

    IIRC once the Stop has happened, updated firmware will not help until the supply is changed. Next time it won't stop. =^..^=
    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.
    3) if you're going to ask about jams include the jam code.
    4) if you're going to ask about an error code include the error code.


    blackcat: Master Of The Obvious =^..^=

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •