Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 24

Thread: C284e dead

  1. #11
    Senior Tech 100+ Posts Zesti's Avatar
    Join Date
    Jun 2009
    Posts
    159
    Rep Power
    21

    Re: C284e dead

    Quote Originally Posted by mrfuser View Post
    Well I download the firmware and tried to upgrade . Even though the screen did nothing the machine rebooted itself and came up to ready State ! Go figure that one out !?!?!?

    Only problem now is it wonít recognize drawer one
    Fuser u'r sooooo lucky..I'm facing same problem in a C554e.....no luck so far....same symptoms of sticking at 2 fins..

    Good for you...

  2. #12
    Senior Tech 100+ Posts Zesti's Avatar
    Join Date
    Jun 2009
    Posts
    159
    Rep Power
    21

    Re: C284e dead

    Quote Originally Posted by mrfuser View Post
    Well I download the firmware and tried to upgrade . Even though the screen did nothing the machine rebooted itself and came up to ready State ! Go figure that one out !?!?!?

    Only problem now is it wonít recognize drawer one
    Fuser u'r sooooo lucky..I'm facing same problem in a C554e.....no luck so far....same symptoms of sticking at 2 fins..

    Good for you...

  3. #13
    Aging Tech 1,000+ Posts
    C284e dead


    Join Date
    Jul 2013
    Location
    Desboro
    Posts
    1,805
    Rep Power
    44

    Re: C284e dead

    Quote Originally Posted by mrfuser View Post
    Well I download the firmware and tried to upgrade . Even though the screen did nothing the machine rebooted itself and came up to ready State ! Go figure that one out !?!?!?

    Only problem now is it wonít recognize drawer one
    If you have access, you should install SSD repair firmware. It may keep this problem from happening again.

  4. #14
    Service Manager 1,000+ Posts
    C284e dead

    mrfuser's Avatar
    Join Date
    May 2007
    Posts
    1,210
    Rep Power
    0

    Re: C284e dead

    Iíll give it a shot today. Going to take another tray to swap.


    Quote Originally Posted by allan View Post
    ??? means it is between sizes. Remove the tray and check the slides on the tray and the sensors at the back inside the machine.
    Set both trays the same and compare the sensor checks.

  5. #15
    RTFM!! 2,500+ Posts allan's Avatar
    Join Date
    Apr 2010
    Location
    Centurion
    Posts
    2,931
    Rep Power
    59

    Re: C284e dead

    Quote Originally Posted by mrfuser View Post
    Iíll give it a shot today. Going to take another tray to swap.

    Don't just take a tray take the length and with sensor/switch assemblies too. The sensor holder can break.
    Whatever

  6. #16
    Aging Tech 1,000+ Posts
    C284e dead


    Join Date
    Jul 2013
    Location
    Desboro
    Posts
    1,805
    Rep Power
    44

    Re: C284e dead

    Quote Originally Posted by mrfuser View Post
    Iíll give it a shot today. Going to take another tray to swap.
    Sometimes if the metal paper guide assembly inside the tray shifts backwards it will cause paper size errors. Make sure the two screws are centred.

  7. #17
    Service Manager 1,000+ Posts
    C284e dead

    mrfuser's Avatar
    Join Date
    May 2007
    Posts
    1,210
    Rep Power
    0

    Re: C284e dead

    Do you know what the sensors are actually called in the parts manual?

  8. #18
    KonicaMinolta Senior Tech 100+ Posts srvctec's Avatar
    Join Date
    Oct 2009
    Location
    Central Kansas
    Posts
    124
    Rep Power
    20

    Re: C284e dead

    Quote Originally Posted by mrfuser View Post
    Do you know what the sensors are actually called in the parts manual?
    Generally they are called size detect sensors.

  9. #19
    RTFM!! 2,500+ Posts allan's Avatar
    Join Date
    Apr 2010
    Location
    Centurion
    Posts
    2,931
    Rep Power
    59

    Re: C284e dead

    Quote Originally Posted by mrfuser View Post
    Do you know what the sensors are actually called in the parts manual?

    Dude pull out a tray get on your ass and have a look in there. Try opening a parts manual.
    Whatever

  10. #20
    Service Manager 1,000+ Posts
    C284e dead

    mrfuser's Avatar
    Join Date
    May 2007
    Posts
    1,210
    Rep Power
    0

    Re: C284e dead

    Dude! 🤪😂
    thanks I needed a chuckle!

    Quote Originally Posted by allan View Post
    Dude pull out a tray get on your ass and have a look in there. Try opening a parts manual.

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •