Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 24

Thread: C284e dead

  1. #11
    Senior Tech 250+ Posts Zesti's Avatar
    Join Date
    Jun 2009
    Posts
    283
    Rep Power
    33

    Re: C284e dead

    Quote Originally Posted by mrfuser View Post
    Well I download the firmware and tried to upgrade . Even though the screen did nothing the machine rebooted itself and came up to ready State ! Go figure that one out !?!?!?

    Only problem now is it won’t recognize drawer one
    Fuser u'r sooooo lucky..I'm facing same problem in a C554e.....no luck so far....same symptoms of sticking at 2 fins..

    Good for you...

  2. #12
    Senior Tech 250+ Posts Zesti's Avatar
    Join Date
    Jun 2009
    Posts
    283
    Rep Power
    33

    Re: C284e dead

    Quote Originally Posted by mrfuser View Post
    Well I download the firmware and tried to upgrade . Even though the screen did nothing the machine rebooted itself and came up to ready State ! Go figure that one out !?!?!?

    Only problem now is it won’t recognize drawer one
    Fuser u'r sooooo lucky..I'm facing same problem in a C554e.....no luck so far....same symptoms of sticking at 2 fins..

    Good for you...

  3. #13
    Aging Tech 10,000+ Posts
    C284e dead

    copier addict's Avatar
    Join Date
    Jul 2013
    Location
    Diamond
    Posts
    11,917
    Rep Power
    322

    Re: C284e dead

    Quote Originally Posted by mrfuser View Post
    Well I download the firmware and tried to upgrade . Even though the screen did nothing the machine rebooted itself and came up to ready State ! Go figure that one out !?!?!?

    Only problem now is it won’t recognize drawer one
    If you have access, you should install SSD repair firmware. It may keep this problem from happening again.

  4. #14
    Service Manager 1,000+ Posts
    C284e dead

    mrfuser's Avatar
    Join Date
    May 2007
    Posts
    1,557
    Rep Power
    51

    Re: C284e dead

    I’ll give it a shot today. Going to take another tray to swap.


    Quote Originally Posted by allan View Post
    ??? means it is between sizes. Remove the tray and check the slides on the tray and the sensors at the back inside the machine.
    Set both trays the same and compare the sensor checks.

  5. #15
    RTFM!! 5,000+ Posts allan's Avatar
    Join Date
    Apr 2010
    Location
    Centurion
    Posts
    5,387
    Rep Power
    152

    Re: C284e dead

    Quote Originally Posted by mrfuser View Post
    I’ll give it a shot today. Going to take another tray to swap.

    Don't just take a tray take the length and with sensor/switch assemblies too. The sensor holder can break.
    Whatever

  6. #16
    Aging Tech 10,000+ Posts
    C284e dead

    copier addict's Avatar
    Join Date
    Jul 2013
    Location
    Diamond
    Posts
    11,917
    Rep Power
    322

    Re: C284e dead

    Quote Originally Posted by mrfuser View Post
    I’ll give it a shot today. Going to take another tray to swap.
    Sometimes if the metal paper guide assembly inside the tray shifts backwards it will cause paper size errors. Make sure the two screws are centred.

  7. #17
    Service Manager 1,000+ Posts
    C284e dead

    mrfuser's Avatar
    Join Date
    May 2007
    Posts
    1,557
    Rep Power
    51

    Re: C284e dead

    Do you know what the sensors are actually called in the parts manual?

  8. #18
    Former KM Senior Tech 500+ Posts srvctec's Avatar
    Join Date
    Oct 2009
    Location
    Central Kansas
    Posts
    827
    Rep Power
    63

    Re: C284e dead

    Quote Originally Posted by mrfuser View Post
    Do you know what the sensors are actually called in the parts manual?
    Generally they are called size detect sensors.

  9. #19
    RTFM!! 5,000+ Posts allan's Avatar
    Join Date
    Apr 2010
    Location
    Centurion
    Posts
    5,387
    Rep Power
    152

    Re: C284e dead

    Quote Originally Posted by mrfuser View Post
    Do you know what the sensors are actually called in the parts manual?

    Dude pull out a tray get on your ass and have a look in there. Try opening a parts manual.
    Whatever

  10. #20
    Service Manager 1,000+ Posts
    C284e dead

    mrfuser's Avatar
    Join Date
    May 2007
    Posts
    1,557
    Rep Power
    51

    Re: C284e dead

    Dude! 🤪😂
    thanks I needed a chuckle!

    Quote Originally Posted by allan View Post
    Dude pull out a tray get on your ass and have a look in there. Try opening a parts manual.

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here