Results 1 to 7 of 7

Thread: c360

  1. #1
    houseec
    Guest

    c360

    bizhub c360 not copying say ready to accept anther jop how to make copying directly

  2. #2
    Aging Tech 10,000+ Posts
    c360

    copier addict's Avatar
    Join Date
    Jul 2013
    Location
    Diamond
    Posts
    12,002
    Rep Power
    325

    Re: c360

    Quote Originally Posted by houseec View Post
    bizhub c360 not copying say ready to accept anther jop how to make copying directly
    One or more of your consumables has likely reached end of life.

  3. #3
    Technician
    Join Date
    Feb 2019
    Location
    Fife
    Posts
    21
    Rep Power
    11

    Re: c360

    Quote Originally Posted by copier addict View Post
    One or more of your consumables has likely reached end of life.
    If it was EOL on these machines you would get a warning first, usually a full panel red error detailing the consumables in question.

    If the firmware on the machine has been updated and software switches 55 and 51 have been set as per the bulletin the full screen error will not show and the machine will not stop when life limit is reached.

    This can be checked if there is an Oil Can showing on the bottom of the display and any of the L codes are showing e.g

    L-1 Cyan
    L-2 Magenta
    L-3 Yellow
    L-4 Black
    L-5 Transfer Belt

    Can also be viewed through web interface.

    So, OP, do you have to dismiss an error before you can view the copy screen, if so you are needing some drums.

    If you are a tech, and you are happy with the print quality (55 halftone, no lines etc etc) download the last available firmware for your machine and install, if memory serves me right it has to be FW G00-C2 or higher . Then perform steps detailed in the Consumable End Of Life Bulletin

    However, if your machine has the switches set correctly already you may be looking for other avenues of failure. I've had issues before with the front PCB behind the waste toner, leading to a stabilising loop. This usually triggers the "Panel is illuminated due to a warning" message and the P codes to match. Without any other information I'm just stabbing in the dark.

  4. #4
    Aging Tech 10,000+ Posts
    c360

    copier addict's Avatar
    Join Date
    Jul 2013
    Location
    Diamond
    Posts
    12,002
    Rep Power
    325

    Re: c360

    Quote Originally Posted by Slammers View Post
    If it was EOL on these machines you would get a warning first, usually a full panel red error detailing the consumables in question.

    If the firmware on the machine has been updated and software switches 55 and 51 have been set as per the bulletin the full screen error will not show and the machine will not stop when life limit is reached.

    This can be checked if there is an Oil Can showing on the bottom of the display and any of the L codes are showing e.g

    L-1 Cyan
    L-2 Magenta
    L-3 Yellow
    L-4 Black
    L-5 Transfer Belt

    Can also be viewed through web interface.

    So, OP, do you have to dismiss an error before you can view the copy screen, if so you are needing some drums.

    If you are a tech, and you are happy with the print quality (55 halftone, no lines etc etc) download the last available firmware for your machine and install, if memory serves me right it has to be FW G00-C2 or higher . Then perform steps detailed in the Consumable End Of Life Bulletin

    However, if your machine has the switches set correctly already you may be looking for other avenues of failure. I've had issues before with the front PCB behind the waste toner, leading to a stabilising loop. This usually triggers the "Panel is illuminated due to a warning" message and the P codes to match. Without any other information I'm just stabbing in the dark.
    I am pretty sure even with the soft switches set if the memory switch in enhanced security is set to "stop" it will not allow a copy and there is no error except possibly an oil can at the bottom

  5. #5
    houseec
    Guest

    Re: c360

    Quote Originally Posted by copier addict View Post
    One or more of your consumables has likely reached end of life.
    i cheak all consumables but still same problem

  6. #6
    Technician
    Join Date
    Feb 2019
    Location
    Fife
    Posts
    21
    Rep Power
    11

    Re: c360

    Quote Originally Posted by copier addict View Post
    I am pretty sure even with the soft switches set if the memory switch in enhanced security is set to "stop" it will not allow a copy and there is no error except possibly an oil can at the bottom
    Ah yeah, you're right. Didn't even think about that. Why you would set the switches and then not set the no stop is questionable but even after my short time as a tech I've seen some fantastic things.

  7. #7
    Service Manager 5,000+ Posts tsbservice's Avatar
    Join Date
    May 2007
    Posts
    7,145
    Rep Power
    346

    Thumbs up Re: c360

    Quote Originally Posted by Slammers View Post
    Ah yeah, you're right. Didn't even think about that. Why you would set the switches and then not set the no stop is questionable but even after my short time as a tech I've seen some fantastic things.
    Looks like your short time as a tech is pretty well spend.
    A tree is known by its fruit, a man by his deeds. A good deed is never lost, he who sows courtesy, reaps friendship, and he who plants kindness gathers love.

    Blessed are they who can laugh at themselves, for they shall never cease to be amused.

    I don't reply to private messages from end users.

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here