Results 1 to 7 of 7
  1. #1
    Trusted Tech 50+ Posts
    Join Date
    Aug 2013
    Location
    New Philadelphia, OH
    Posts
    91
    Rep Power
    0

    bizhub C454 and J99-01

    I don't usually ask many questions here but when I do, someone always provides some good info. I have a bizhub C454 that is producing a 99-01 misfeed code on every single job fro the bypass tray. It only jams when using the bypass...trays 1,2 and 3 (pc-410) all work fine. the paper stops in the fuser with 1/3 hanging out of the bottom and a 1/3 sticking out of the top. I have replaced the bypass clutch CL7 as well as M1 and M3 motors. I have also loaded the latest firmware G00-72. I haven't been able to find a lot of info on this code so any info would be appreciated. Thanks

  2. #2
    RTFM!! 5,000+ Posts allan's Avatar
    Join Date
    Apr 2010
    Location
    Centurion
    Posts
    5,387
    Rep Power
    152

    Re: bizhub C454 and J99-01

    The J99-xx jam codes are classed as engine jams(logical jam). The machine jams because of unexpected timing. Paper not the size the machine is expecting.
    Could be as simple as the paper specified and the paper supplied does not match up.

    There is a width calibration that needs to be done on the bypass if it is out of wack. It uses the width and checks that against the standard paper sizes to determine the length.
    So that means if your paper is of an odd lenght then you need to measure the XY dimensions and setup a custom size.
    If you are using standard sizes make sure the machine is set to inch or metric as per your area.
    Whatever

  3. #3
    Service Manager 5,000+ Posts
    bizhub C454 and J99-01

    copier tech's Avatar
    Join Date
    Jan 2014
    Location
    London
    Posts
    7,531
    Rep Power
    182

    Re: bizhub C454 and J99-01

    Try using SW69 set to HEX 01 uses the driver setting for size.

    Or you can use SW145 HEX 02 displays paper mismatch rather than jamming.
    Let us eat, drink, and be merry, because tomorrow we may die!

    For all your firmware & service manual needs please visit us at:

    www.copierfirmware.co.uk - www.printerfirmware.co.uk




  4. #4
    Trusted Tech 50+ Posts
    Join Date
    Aug 2013
    Location
    New Philadelphia, OH
    Posts
    91
    Rep Power
    0

    Re: bizhub C454 and J99-01

    Quote Originally Posted by allan View Post
    The J99-xx jam codes are classed as engine jams(logical jam). The machine jams because of unexpected timing. Paper not the size the machine is expecting.
    Could be as simple as the paper specified and the paper supplied does not match up.

    There is a width calibration that needs to be done on the bypass if it is out of wack. It uses the width and checks that against the standard paper sizes to determine the length.
    So that means if your paper is of an odd lenght then you need to measure the XY dimensions and setup a custom size.
    If you are using standard sizes make sure the machine is set to inch or metric as per your area.

    thanks for the reply...I've checked paper settings against paper being used but I have not done any calibrations on the bypass itself so I will give that a try tomorrow.

  5. #5
    Trusted Tech 50+ Posts
    Join Date
    Aug 2013
    Location
    New Philadelphia, OH
    Posts
    91
    Rep Power
    0

    Re: bizhub C454 and J99-01

    Quote Originally Posted by copier tech View Post
    Try using SW69 set to HEX 01 uses the driver setting for size.

    Or you can use SW145 HEX 02 displays paper mismatch rather than jamming.
    thanks for the info...I just read this in another thread...will give it a try when I return.

  6. #6
    Service Manager 2,500+ Posts
    bizhub C454 and J99-01


    Join Date
    Sep 2005
    Location
    South Jersey
    Posts
    3,831
    Rep Power
    133

    Re: bizhub C454 and J99-01

    If it is stopping in the same "exact" spot every time then agree with the others it might be reading the paper size wrong. You've replaced all relevant parts except you didn't mention any sensors, did you try swapping any of the ones exclusive to the bypass?

  7. #7
    Trusted Tech 50+ Posts
    Join Date
    Aug 2013
    Location
    New Philadelphia, OH
    Posts
    91
    Rep Power
    0

    Re: bizhub C454 and J99-01

    Quote Originally Posted by copier tech View Post
    Try using SW69 set to HEX 01 uses the driver setting for size.

    Or you can use SW145 HEX 02 displays paper mismatch rather than jamming.
    Thank you for this...worked perfectly.

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here