+ Reply to Thread
Page 1 of 2
1 2 LastLast
Results 1 to 10 of 13

Thread: Bizhub C10 "Please wait"

  1. #1
    Junior Member llla is on a distinguished road
    Join Date
    Jun 2009
    Location
    Oslo
    Posts
    8
    Rep Power
    0

    Question Bizhub C10 "Please wait"

    Hi.
    I have a bizhub C10 with the message "please wait" stuck i display. Engine and fan`s starting up but "Please wait" msg stuck in display.

  2. #2
    Trusted Tech 50+ Posts jprecht is building a good name for himself jprecht's Avatar
    Join Date
    Dec 2008
    Location
    La Grange, Texas
    Posts
    87
    Rep Power
    3

    wait indie

    when u pwr up do you see fuser lmp and hear cycling??? copier cycles then stops? may need to replace hdd and/or reflash firmware. have seen this on bizhub c250 good luck!!!! jprecht p s did you "re-initialize"??? first not familiar with this unit but have several 250c 350c ect out there.

  3. #3
    Junior Member llla is on a distinguished road
    Join Date
    Jun 2009
    Location
    Oslo
    Posts
    8
    Rep Power
    0
    I hear mc i cycles up. I`ll try to rewrite fw to see if that help. Thanks

  4. #4
    KonicaMinolta Engineer 100+ Posts minimerlin is on a distinguished road minimerlin's Avatar
    Join Date
    Nov 2007
    Posts
    243
    Rep Power
    7
    Quote Originally Posted by llla View Post
    Hi.
    I have a bizhub C10 with the message "please wait" stuck i display. Engine and fan`s starting up but "Please wait" msg stuck in display.
    Was the C10 asking for any units to be changed prior to this indication...sounds like it is trying to carry out a calibration.

  5. #5
    Junior Member llla is on a distinguished road
    Join Date
    Jun 2009
    Location
    Oslo
    Posts
    8
    Rep Power
    0
    Quote Originally Posted by minimerlin View Post
    Was the C10 asking for any units to be changed prior to this indication...sounds like it is trying to carry out a calibration.
    No, costumer had just turned it on and no other msg than "Please wait".
    I tried to wait 10 min but msg was still there. I tried to power it off/on several times but it just starts engine, rotate whats supposed to rotate, I hear fans starting, just like normal. But msg say Please wait. So like jprecht I think it is fw or some electronical problem. I`ll try fw rewrite tomorrow.

  6. #6
    Trusted Tech 50+ Posts jprecht is building a good name for himself jprecht's Avatar
    Join Date
    Dec 2008
    Location
    La Grange, Texas
    Posts
    87
    Rep Power
    3

    reboot

    not familiar with this one but almost all bizhubs have a service pcb with two pins you short to re-initialize short pins cheat door sw depress service trouble reset button hold it down while turning on copier wait 10 sec, release i would try this first . good luck!!!

  7. #7
    Junior Member llla is on a distinguished road
    Join Date
    Jun 2009
    Location
    Oslo
    Posts
    8
    Rep Power
    0
    I loaded new fw today but mc still show same msg, but I saw that exp lamp did not light up so I`ll try to change CCD assy.

  8. #8
    Trusted Tech 50+ Posts tarzak911 is on a distinguished road
    Join Date
    Feb 2009
    Location
    CAPE TOWN
    Posts
    54
    Rep Power
    3
    not ccd ... fuser lamp...

  9. #9
    Technician peter lynn is on a distinguished road
    Join Date
    Dec 2007
    Location
    bridgend
    Posts
    24
    Rep Power
    5

    Wink

    Quote Originally Posted by llla View Post
    Hi.
    I have a bizhub C10 with the message "please wait" stuck i display. Engine and fan`s starting up but "Please wait" msg stuck in display.
    the fuser is fed via a microswitc h operated by a plunger/on left side top covercheck pivot point ofthis operating lever--it breaks--and replace the switch (same as front door switch on 7033/7045)
    you wll kiss goodbye to 2 hours for this.(follow change fuser instructions for access)
    happy copying peter

  10. #10
    Senior Tech 100+ Posts tech51 is on a distinguished road
    Join Date
    Jan 2009
    Location
    Suffolk
    Posts
    105
    Rep Power
    4
    Your spot on with the ccd/lamp assembly, just had a tech memo saying this is probable cause of please wait message. Go for it!!!

+ Reply to Thread
Page 1 of 2
1 2 LastLast

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts