Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Page 1 of 2 12 LastLast
Results 1 to 10 of 11
  1. #1
    Technician
    Join Date
    Jan 2010
    Posts
    20
    Rep Power
    16

    CF2002 stuck in bootup mode

    I have a CF 2002 which as of recently, when I turn it on, it warms up and stays stuck on the "Konica" bootup screen, and won't fully initialize. Not sure what the problem is , or if there is anything I should be checking. Is there a default initilization process I can try or does it sound like a bad component.

    Any ideas would be appreciated.

    Thanks,
    Michael


  2. #2
    Junior Member
    Join Date
    Sep 2008
    Location
    grimslov
    Posts
    9
    Rep Power
    0
    Quote Originally Posted by Guitarist69 View Post
    I have a CF 2002 which as of recently, when I turn it on, it warms up and stays stuck on the "Konica" bootup screen, and won't fully initialize. Not sure what the problem is , or if there is anything I should be checking. Is there a default initilization process I can try or does it sound like a bad component.

    Any ideas would be appreciated.

    Thanks,
    Michael
    Hello,
    Follow the instructions in the attached document, had the same problem and this worked for me!

    regards, Henrik

    Attached Files Attached Files

  3. #3
    Technician
    Join Date
    Jan 2010
    Posts
    20
    Rep Power
    16
    Unfortunately I am not getting that error code.

    Any other thoughts - There has got to be a way to hard reset the system back to default without accessing Tech -mode, wehich I can't get to


  4. #4
    Junior Member
    Join Date
    May 2010
    Location
    islamabad
    Posts
    5
    Rep Power
    0

    minolta cf 2002

    hello every one

    i have [ Minolta CF 2002 ] machine.

    the machine software support Microsoft office printing but not adobe pdf file.also printing jpg and other format but not either adobe pdf file.


    can any one help me plz

    bundle of thanx


  5. #5
    Senior Tech 100+ Posts oldschool's Avatar
    Join Date
    Mar 2007
    Location
    Ithaca NY
    Posts
    210
    Rep Power
    24
    I haven't touched a CF2002 in a while but I seem to remember the connector from the scanner to the printer being problematic. You could easily bend pins and cause strange problems.


  6. #6
    Junior Member
    Join Date
    Feb 2009
    Location
    Hornby Island, BC
    Posts
    6
    Rep Power
    0

    CF2002 stuck in bootup mode

    I've had the same thing happening recently and what I've figured out
    is the hard drive needs to be replaced. You might want to check that.

    If the machine is shut down improperly or power outage shuts it down,
    the data on the drive may get corrupted.

    I'm trying to get a hold of the Fiery X3e for CF2002 software cd, so I can
    load it onto a different hard drive. Apparently you need a PC with a parallel printer port to do
    the software install.

    Charlie


  7. #7
    Senior Tech 100+ Posts
    Join Date
    Mar 2009
    Posts
    165
    Rep Power
    0
    Quote Originally Posted by cwood View Post
    I've had the same thing happening recently and what I've figured out
    is the hard drive needs to be replaced. You might want to check that.

    If the machine is shut down improperly or power outage shuts it down,
    the data on the drive may get corrupted.

    I'm trying to get a hold of the Fiery X3e for CF2002 software cd, so I can
    load it onto a different hard drive. Apparently you need a PC with a parallel printer port to do
    the software install.

    Charlie
    To re-install you must also be able to use command prompt control language, the cable is a parallel to serial (25 pin i think). there is a special program from KM to speed up printer port communication.(xp and above)....if you do not use it you can get timeouts and waste hours of effort. the printer port must also be setup a certain way in the computer bios. there is a bulletin with specific instructions available

    Sorry folks, reputation removed by Just Manuals, because he's a sad little wanker

  8. #8
    Junior Member
    Join Date
    May 2010
    Location
    islamabad
    Posts
    5
    Rep Power
    0
    actually when i install driver and also install java on windows xp sp3 ok.
    but fiery do not print at all.if some give me complete process of installing driver withj jpg or give me web site to getting some information thanx.


  9. #9
    Technician Johnny_B500's Avatar
    Join Date
    Mar 2007
    Posts
    24
    Rep Power
    22
    I had the 'stuck on the Konica bootup screen' issue a few months ago. There is an internal hard drive in the back of the CF2002 (not the Fiery hard drive). I replaced it and all was resolved.


  10. #10
    Technician
    Join Date
    Jan 2011
    Location
    terrace
    Posts
    21
    Rep Power
    14

    Re: CF2002 stuck in bootup mode

    Quote Originally Posted by Guitarist69 View Post
    Unfortunately I am not getting that error code.

    Any other thoughts - There has got to be a way to hard reset the system back to default without accessing Tech -mode, wehich I can't get to

    hi I am having the exact same problem and wondering if you found a solution?? thanks


Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •