Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Page 2 of 2 FirstFirst 12
Results 11 to 14 of 14
  1. #11
    Service Manager 1,000+ Posts
    c220 document feeder jamming df617 samething whit c203 df611

    habik's Avatar
    Join Date
    Apr 2010
    Posts
    2,015
    Rep Power
    59

    Re: c220 document feeder jamming df617 samething whit c203 df611

    Quote Originally Posted by habik View Post
    Old thread new problem with C203 DF-611

    Did MOD of the paper lift motor plate KM
    Did MOD of the paper lift plate as per Mercutio Norway
    Did Mod as per Emujo rear screws removal

    Have New tyres, other rollers and Sensors plus black pads are pristine clean, when loaded full to top machine jams half way usually with 6603.

    When doing ADF paper passage test single or double in Service mode the machine freezes when above 6603 jam occurs.Tried different doc feeder same issue. Reboot required each time.

    Reloaded with R6 firmware. Same thing.

    Dusted all boards, power supply as it came from building site.

    Now it does not freeze anymore, after massive dusting mayhem of the whole machine, it still jams in ADF usually half way through full load.

    Any suggestions other than Sledge hammer...as I already have it on hand.

    Thanks
    Another Freeze out ...its Summer for heaven sake any insides guys on this?
    .OK Google! ... will I need Berrocca this morning?
    Firmwares HERE

  2. #12
    Senior Tech 100+ Posts Brett GS's Avatar
    Join Date
    Jun 2013
    Location
    N/A
    Posts
    154
    Rep Power
    23

    Re: c220 document feeder jamming df617 samething whit c203 df611

    Quote Originally Posted by emujo View Post
    I've had tremendous success with a non approved method on these ADFs. Remove the 2 rear screws that secure the cover that gives you access to the feed rollers. Just dump them in the bushes!!!! Every one that I've been to that didn't need a new lift motor, or had worn out rubber has worked after this. I believe the cover is too close to the lip the paper feeds over and removing these screws allows enough clearance. Runs the same as if the screws were installed. Emujo
    is it the rear screws either side of that flap or tne screws at the back of the df flap if standing in front of the machine.

  3. #13
    Senior Tech 250+ Posts
    c220 document feeder jamming df617 samething whit c203 df611


    Join Date
    Mar 2009
    Posts
    408
    Rep Power
    37

    Re: c220 document feeder jamming df617 samething whit c203 df611

    I'm confused aswell which screws :P. Lots of self tappers you mean remove two of the four screws that give you access to the feed tyres if you where replacing them?

  4. #14
    Field Supervisor 500+ Posts
    c220 document feeder jamming df617 samething whit c203 df611

    minimerlin's Avatar
    Join Date
    Nov 2007
    Location
    Scottish Highlands
    Posts
    851
    Rep Power
    44

    Re: c220 document feeder jamming df617 samething whit c203 df611

    I just replace the feed and sep rollers with the red paper tray ones...you have to slide the actual tyre off the shaft section to fit the sep roller but it is easy to do. Seems to clear up the problem for me.

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here