Page 2 of 4 FirstFirst 1234 LastLast
Results 11 to 20 of 33
  1. #11
    Service Manager 5,000+ Posts
    error code 0094 on a Konica Minolta C35

    copier tech's Avatar
    Join Date
    Jan 2014
    Location
    London
    Posts
    7,531
    Rep Power
    182

    Re: error code 0094 on a Konica Minolta C35

    I have just seen this fault for myself, my fix was the solenoid pad, for the record it's not on the solenoid but on the fame, not easy to see, I used a torch (flashlight)
    Pressing the solinoid by hand there was a delay due to the pad going stickey, after I removed the pad the arm returned back instantly.

    So thanks again CopyTech!
    Let us eat, drink, and be merry, because tomorrow we may die!

    For all your firmware & service manual needs please visit us at:

    www.copierfirmware.co.uk - www.printerfirmware.co.uk




  2. #12
    Trusted Tech 50+ Posts
    Join Date
    Sep 2013
    Location
    Eagan, MN
    Posts
    79
    Rep Power
    22

    Re: error code 0094 on a Konica Minolta C35

    I have had this 3 times and all were fixed by replacing the whole right side door assembly and its wiring. Get either a used one or order the whole assembly from KM.

  3. #13
    Step aside, noob 1,000+ Posts EarthKmTech's Avatar
    Join Date
    May 2009
    Location
    Gigety
    Posts
    2,141
    Rep Power
    75

    Re: error code 0094 on a Konica Minolta C35

    Quote Originally Posted by minimerlin View Post
    Remove the ITB and then remove the 4 springs that are visible holding the Magenta and Yellow 1st transfer rollers in tension. Refit the belt..if code stays away you are supposed to remove the belt and refit the springs after stretching them a little to reduce their tension but not so much that they fall off!!
    The springs are too tight so that the drives cannot operate the shift assembly, hence the noise and then the code!

    Sorry ...Just realised that I have missread the error code!! Please ignore my post..talking about 0096 code.
    I had this recently - I cant beleive how hard it is to turn the gear to actuate the transfer rollers inside the belts on these machines, no wonder it causes troubles. Do you actually delve into the main drive unit and fix this problem when it breaks properly or just throw the machine away and replace it like us ?

  4. #14
    Senior Tech 250+ Posts MFPTech's Avatar
    Join Date
    Nov 2010
    Location
    Surrey
    Posts
    486
    Rep Power
    33

    Re: error code 0094 on a Konica Minolta C35

    Quote Originally Posted by EarthKmTech View Post
    I had this recently - I cant beleive how hard it is to turn the gear to actuate the transfer rollers inside the belts on these machines, no wonder it causes troubles. Do you actually delve into the main drive unit and fix this problem when it breaks properly or just throw the machine away and replace it like us ?
    All you have to do is remove the foam at the solenoid - simple as that!
    Thanks again to the first tech that pointed out this solution!

  5. #15
    Service Manager 2,500+ Posts
    error code 0094 on a Konica Minolta C35

    Hansoon's Avatar
    Join Date
    Sep 2007
    Posts
    3,190
    Rep Power
    94

    Re: error code 0094 on a Konica Minolta C35

    All you have to do is remove the foam at the solenoid - simple as that!
    But replace with at least a piece of tape. Otherwise the metal parts can stick together due to remnant magnetic force.

    Hans
    " Sent from my Intel 80286 using MS-DOS 2.0 "

  6. #16
    Service Manager 5,000+ Posts
    error code 0094 on a Konica Minolta C35

    copier tech's Avatar
    Join Date
    Jan 2014
    Location
    London
    Posts
    7,531
    Rep Power
    182

    Re: error code 0094 on a Konica Minolta C35

    I stretched the solenoid sping to help it spring back that helped!
    Let us eat, drink, and be merry, because tomorrow we may die!

    For all your firmware & service manual needs please visit us at:

    www.copierfirmware.co.uk - www.printerfirmware.co.uk




  7. #17
    Master Of The Obvious 10,000+ Posts
    error code 0094 on a Konica Minolta C35

    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    22,444
    Rep Power
    462

    Re: error code 0094 on a Konica Minolta C35

    Quote Originally Posted by copier tech View Post
    I have just seen this fault for myself, my fix was the solenoid pad, for the record it's not on the solenoid but on the fame, not easy to see, I used a torch (flashlight)
    Pressing the solinoid by hand there was a delay due to the pad going stickey, after I removed the pad the arm returned back instantly.

    So thanks again CopyTech!
    Quote Originally Posted by Hansoon View Post
    But replace with at least a piece of tape. Otherwise the metal parts can stick together due to remnant magnetic force.

    Hans
    Hans is right. Without some sort sort of damper the actuator will magnetize, acting exactly like the sticky foam pad.

    But feel free to ignore Hans. It will bite you on the ass soon enough. Hopefully you'll learn to listen to good advice eventually. =^..^=
    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.
    3) if you're going to ask about jams include the jam code.
    4) if you're going to ask about an error code include the error code.
    5) You are the person onsite. Only you can make observations.

    blackcat: Master Of The Obvious =^..^=

  8. #18
    Technician
    error code 0094 on a Konica Minolta C35

    Mr. Joshua's Avatar
    Join Date
    Nov 2011
    Location
    Midwest US
    Posts
    31
    Rep Power
    26

    Re: error code 0094 on a Konica Minolta C35

    Quote Originally Posted by Hansoon View Post
    But replace with at least a piece of tape. Otherwise the metal parts can stick together due to remnant magnetic force.

    Hans
    Yes, thanks for catching that Hans, very important!

  9. #19
    Step aside, noob 1,000+ Posts EarthKmTech's Avatar
    Join Date
    May 2009
    Location
    Gigety
    Posts
    2,141
    Rep Power
    75

    Re: error code 0094 on a Konica Minolta C35

    FYI, i was talking about permanent transfer belt retraction troubles, not transfer roller retraction troubles - i should not of added confusion to the post.

    that machine has since been scrapped as the labour to repair is worth more than the value of the machine.

  10. #20
    Service Manager 1,000+ Posts
    Join Date
    Sep 2012
    Posts
    1,129
    Rep Power
    39
    I've had this about three times also and fixed by replacing the right door assy. I do it now in about 45 min or less. Most of the work is to get the wire harness of this assy to the prcb on the other side of the device. You have to remove the adf, scanner, HDD, fax card, control panel, and covers of course.

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here