Page 1 of 2 12 LastLast
Results 1 to 10 of 15
  1. #1
    Trusted Tech 50+ Posts
    Join Date
    Jun 2009
    Location
    New York, NY
    Posts
    87
    Post Thanks / Like
    Rep Power
    0

    Konica Minolta Bizhub C250 - Jamming before going into Fuser unit

    Hi Everyone,

    I have a Kon Min C250 that is jamming like a z fold before it gets to the Fuser unit. I have check the registration roller that is what usually happen but it seem to be working OK.

    Any ideas what can it be? Any help would be greatly appreciated.

    Thanks,
    Rad


  2. #2
    Trusted Tech 50+ Posts boanda's Avatar
    Join Date
    Feb 2011
    Posts
    79
    Post Thanks / Like
    Rep Power
    0

    Re: Konica Minolta Bizhub C250 - Jamming before going into Fuser unit

    paper miss fuser, is fuser ok?


  3. #3
    Trusted Tech 50+ Posts
    Join Date
    Jun 2009
    Location
    New York, NY
    Posts
    87
    Post Thanks / Like
    Rep Power
    0

    Re: Konica Minolta Bizhub C250 - Jamming before going into Fuser unit

    Fuser working ok. I try another fuser from another machine that is working.

    Thks,
    Rad


  4. #4
    Field Supervisor 1,000+ Posts
    Join Date
    Jun 2009
    Posts
    2,117
    Post Thanks / Like
    Rep Power
    58

    Re: Konica Minolta Bizhub C250 - Jamming before going into Fuser unit

    You said you checked the 2nd X-fer roller...what does this mean? Try replacing the roller, as this is a usual symptom when it starts to go...visual inspection won't tell you much. Emujo


  5. #5
    Technician
    Join Date
    Aug 2009
    Location
    St. Paul, MN
    Posts
    12
    Post Thanks / Like
    Rep Power
    11

    Unhappy Re: Konica Minolta Bizhub C250 - Jamming before going into Fuser unit

    I am having the same problem on my CF 3102.

    The paper jams right when it gets to the fuser unit.

    I replaced the fuser unit with another one, and it still has the same problem.

    When you say replace the 2nd x-fer roller, what do you mean?

    Is it in the door, or in the fuser unit?

    I know it's an old machine, but I can't afford a new one right now.

    Any help would be much appreciated.

    Thanks in advance... desperate..


  6. #6
    Technician bhangdu's Avatar
    Join Date
    Nov 2010
    Posts
    15
    Post Thanks / Like
    Rep Power
    8

    Re: Konica Minolta Bizhub C250 - Jamming before going into Fuser unit

    Did you checked the 2nd transfer roller gear & pin


  7. #7
    Technician
    Join Date
    Aug 2009
    Location
    St. Paul, MN
    Posts
    12
    Post Thanks / Like
    Rep Power
    11

    Unhappy Re: Konica Minolta Bizhub C250 - Jamming before going into Fuser unit

    Hi Bhangdu,

    Could you tell me where that is?

    Thanks


  8. #8
    Field Supervisor 5,000+ Posts


    JustManuals.com's Avatar
    Join Date
    Jan 2006
    Location
    Las Vegas, NV
    Posts
    10,478
    Post Thanks / Like
    Rep Power
    133

    Lightbulb Re: Konica Minolta Bizhub C250 - Jamming before going into Fuser unit

    This Parts & Service manual can now be purchased for $12.77 and downloaded immediately after payment from

    Just Manuals ~ The Internet's largest selection of manuals ~ Instant Downloads


    Paul@justmanuals.com


    When you need a manual and you need it NOW !

    http://www.justmanuals.com
    Instant downloads

  9. #9
    Trusted Tech 50+ Posts
    Join Date
    Feb 2011
    Location
    tamilnadu,madurai
    Posts
    54
    Post Thanks / Like
    Rep Power
    0

    Lightbulb Re: Konica Minolta Bizhub C250 - Jamming before going into Fuser unit

    hi friend check just check fusing unit gear leaver. that leaver open when right side door closing. i think right side door not closing properly.


  10. #10
    Service Manager 250+ Posts kingarthur's Avatar
    Join Date
    Feb 2008
    Posts
    491
    Post Thanks / Like
    Rep Power
    19

    Re: Konica Minolta Bizhub C250 - Jamming before going into Fuser unit

    i had this on a C203....is there any print on the page...if not it IS the transfer roller in the door..i kept thinking it was a fuser problem.. cos everytime i opened the door the paper was at the entrance to the fuser, but the transfer roller was causing the problem by stopping the paper & would "spring" up to the fuser when you opened the door....dont forget that if you are resetting the transfer belt then you probably aren't replacing the transfer roller as well....

    Tip for the day; Treat every problem as your dog would.....If you cant eat it or f*ck it....then p*ss on it & walk away...

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •