Page 1 of 2 12 LastLast
Results 1 to 10 of 12
  1. #1
    Technician
    Join Date
    Mar 2011
    Location
    Santa Ana, Orange County
    Posts
    32
    Post Thanks / Like
    Rep Power
    7

    Tech needed for BizHub Pro 1050EP

    I'm looking for a tech in the Orange County, California area to work on my BizHub Pro 1050EP.

    PM me and leave a contact number or email me at doug@beachmailing.com


    I have a fault on two drawrs out of the three on the large capacity feeder that I can't resolve.

    When I feed from drawer 4 in the PF, I get a J18-07 jam code.

    From the manual - this code says - "The PF exit sensor (PS99) does not turn ON within a specified period of time after the loop sensor /2 (PS94) turns ON."

    So I replaced the Exit sensor - no change

    If I pre-feed a sheet partially through the feed rollers, this sheet feeds fine but the jam code comes up on the second sheet.

    I relaced all of the paper feed rollers - didn't make any difference.

    I'm replaced the torque limiters on all drawers (they needed it anyway) - didn't help.








  2. #2
    Field Supervisor 500+ Posts copytechman's Avatar
    Join Date
    Nov 2008
    Location
    Barrie, Ontario
    Posts
    659
    Post Thanks / Like
    Rep Power
    17

    Re: Tech needed for BizHub Pro 1050EP

    Not sure which feeder it is but have seen cases where the conveying rollers (rubber ones) swell, especially the middle ones, something to look @/think about!

    Regards!
    A.


  3. #3
    Technician
    Join Date
    Mar 2011
    Location
    Santa Ana, Orange County
    Posts
    32
    Post Thanks / Like
    Rep Power
    7

    Re: Tech needed for BizHub Pro 1050EP

    Copytechman,


    Yep - I checked the transport rollers and they looked OK - I cleaned them with rubber conditioner and it didn't help althouh I didn't replace them.

    I'm wondering if the main drive mototo on the feeder might be going out and slowing down - making the whole paper transport slow down.


    I'm trying to avoid just replacing everything though.......


  4. #4
    Technician blago_vd's Avatar
    Join Date
    Apr 2009
    Location
    Sofia
    Posts
    35
    Post Thanks / Like
    Rep Power
    11

    Re: Tech needed for BizHub Pro 1050EP

    Check the couplings between the roller shaft and clutch shaft inside the PF. The easiest way is to remove the side cover of PF, to pull out the drawers and check.


  5. #5
    Field Supervisor 1,000+ Posts RRodgers's Avatar
    Join Date
    Jun 2009
    Location
    San Bernardino
    Posts
    1,830
    Post Thanks / Like
    Rep Power
    33

    Re: Tech needed for BizHub Pro 1050EP

    Quote Originally Posted by blago_vd View Post
    Check the couplings between the roller shaft and clutch shaft inside the PF. The easiest way is to remove the side cover of PF, to pull out the drawers and check.
    do you work on weekends?

    Color is not 4 times harder... it's 65,000 times harder. They call it "TECH MODE" for a reason. I have manual's and firmware for ya, course... you are going to have to earn it. (I'm arrogant LOL)

  6. #6
    Technician
    Join Date
    Mar 2011
    Location
    Santa Ana, Orange County
    Posts
    32
    Post Thanks / Like
    Rep Power
    7

    Re: Tech needed for BizHub Pro 1050EP

    Quote Originally Posted by blago_vd View Post
    Check the couplings between the roller shaft and clutch shaft inside the PF. The easiest way is to remove the side cover of PF, to pull out the drawers and check.
    blago_vd,

    Thanx.

    Which shaft are you talking about? The registrarion conveyance roller? (Item 10 in the drawing below) Looks like this is the shaft that should be driving the paper between the two sensors where it's reporting a problem...


    UpperFeedRoller.jpg

    Doug


  7. #7
    Technician
    Join Date
    Mar 2011
    Location
    Santa Ana, Orange County
    Posts
    32
    Post Thanks / Like
    Rep Power
    7

    Re: Tech needed for BizHub Pro 1050EP

    Quote Originally Posted by RRodgers View Post
    do you work on weekends?
    I usually work sometime over the weekends - but not this weekend 'cause I'm out of town.

    Next weekend would be fine though.

    Do you work on these machines?


  8. #8
    Technician
    Join Date
    Nov 2009
    Posts
    19
    Post Thanks / Like
    Rep Power
    9

    Re: Tech needed for BizHub Pro 1050EP

    think i had this once before when the pin had broken away the inside of the plastic gear (think it was item 19 or 15). This causes loss of drive to the feed, the gear just spins because the moulding for the pin to locate into is broken. Hope this helps!!!


  9. #9
    Field Supervisor 1,000+ Posts RRodgers's Avatar
    Join Date
    Jun 2009
    Location
    San Bernardino
    Posts
    1,830
    Post Thanks / Like
    Rep Power
    33

    Re: Tech needed for BizHub Pro 1050EP

    Quote Originally Posted by scotsman60 View Post
    I usually work sometime over the weekends - but not this weekend 'cause I'm out of town.

    Next weekend would be fine though.

    Do you work on these machines?
    I'm trained on the 1050 but to be honest, I haven't seen one in forever.

    Color is not 4 times harder... it's 65,000 times harder. They call it "TECH MODE" for a reason. I have manual's and firmware for ya, course... you are going to have to earn it. (I'm arrogant LOL)

  10. #10
    Junior Member
    Join Date
    Jun 2011
    Location
    kowlooom
    Posts
    1
    Post Thanks / Like
    Rep Power
    0

    Re: Tech needed for BizHub Pro 1050EP

    Quote Originally Posted by RRodgers View Post
    I'm trained on the 1050 but to be honest, I haven't seen one in forever.
    check the pulley 26T inside the PF drive unit IMG_1416.jpg


Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •