c452 series tray 4 feed assembly is compatible with the c451 series too for anyone distressed at the fact that only the individual parts are listed in the c451 parts manual.
have done it a few times, never had an issue.
c452 series tray 4 feed assembly is compatible with the c451 series too for anyone distressed at the fact that only the individual parts are listed in the c451 parts manual.
have done it a few times, never had an issue.
Firmwares HERE.OK Google! ... will I need Berrocca this morning?
Hi all,
Had similar issue on Bizhub 552 today, ordered and replaced the tray 3 feed assy as it was indeed out of date per bulletins. No difference. Paper from tray 3 only would skew and crumple, sometimes jam. Tore apart and inspected/cleaned the "level conveyance section" and right side door. No difference. Took out tray 2 to watch paper pass from tray 3, was skewing in "level conveyance section".
Further observed paper lifting in tray 3. Looked higher at the rear lead edge. Took out paper (maybe 100 sheets) inspected lifting of tray 3, looked fine. Putting paper back in I noticed 10 dog eared sheets at bottom of pile, looked fine in tray but was lifting the paper just enough at the rear lead edge to catch and skew going through the p/u feed assy.
Sadly I normally check the paper first but it really looked fine in the tray, I even fanned it and didn't see the dog eared sheets.
Issue resolved for me.
Cheers,
Colin
Good thread, I have had that broken door latch on a couple of machines. Its easy to miss. Also some techs are not using the right tools to remove the feed unit and breaks the plastic housing near the clutches. You cant remove it with your normal screwdriver without removing tray one and two first, only shows a crack but causes the machine to jam.
Just an FYI, KM has a new ribbed pickup roller for these models. It is for the trays and the bypass tray. The new 654's are coming with it installed. The part# is A5C1562200. There is a tech bulletin for it.
Cheers Bizhub1 for all your posts. Much appreciated!
Sent from my iDon't believe in marketing device using Tapatalk
Firmwares HERE.OK Google! ... will I need Berrocca this morning?
Firmwares HERE.OK Google! ... will I need Berrocca this morning?
So are these new rollers compatible with the c451/552 series?
Precision Roller lists compatibility with:
- Konica Minolta bizhub 223
- Konica Minolta bizhub 224E
- Konica Minolta bizhub 283
- Konica Minolta bizhub 284E
- Konica Minolta bizhub 36
- Konica Minolta bizhub 363
- Konica Minolta bizhub 364E
- Konica Minolta bizhub 42
- Konica Minolta bizhub 423
- Konica Minolta bizhub 454E
- Konica Minolta bizhub 554E
- Konica Minolta bizhub C220
- Konica Minolta bizhub C224
- Konica Minolta bizhub C224e
- Konica Minolta bizhub C280
- Konica Minolta bizhub C284
- Konica Minolta bizhub C284e
- Konica Minolta bizhub C360
- Konica Minolta bizhub C364
- Konica Minolta bizhub C452
- Konica Minolta bizhub C454
- Konica Minolta bizhub C554
- Konica Minolta LU204
- Konica Minolta LU301
- Konica Minolta PC107
- Konica Minolta PC109
- Konica Minolta PC110
- Konica Minolta PC207
- Konica Minolta PC208
- Konica Minolta PC210
- Konica Minolta PC408
- Konica Minolta PC409
- Konica Minolta PC410
Bookmarks