Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Page 1 of 2 12 LastLast
Results 1 to 10 of 11
  1. #1
    Trusted Tech 50+ Posts
    Join Date
    Oct 2011
    Posts
    72
    Rep Power
    26

    KONICA 7022 Showing "PLEASE ADJUST L DETECTION"

    hi,
    Could somebody help on my Konica 7022 showing "PLEASE ADJUST L DETECTION".
    The problem with this machine before is that all the paper cassette trays and bypass feed tray are not taking up paper, not it is showing the said message.
    Please help.
    Cesar

  2. #2
    Technician
    KONICA 7022 Showing "PLEASE ADJUST L DETECTION"


    Join Date
    Feb 2012
    Location
    near ATL
    Posts
    36
    Rep Power
    25

    Re: KONICA 7022 Showing "PLEASE ADJUST L DETECTION"

    Well, run L Detect. It is in 36 mode. Get into 36 mode by holding down 3 and 6 and powering on the machine.

    Are the paper trays grayed out on the control panel? Does the machines mechanical counter and electronic counters match?

    If you don't have a service manual for this machine, it would be worth the investment.

  3. #3
    Trusted Tech 50+ Posts
    Join Date
    Oct 2011
    Posts
    72
    Rep Power
    26

    Re: KONICA 7022 Showing "PLEASE ADJUST L DETECTION"

    Hi Mr. MCBIG
    Fortunately i managed to reset the L DETECTION PROBLEM, but after i manage to reset it there is a code F26-3 that appears. Is there any chance to reset this code?
    Thank you anyway for kind response.
    Regards,
    Cesar

  4. #4
    Technician
    KONICA 7022 Showing "PLEASE ADJUST L DETECTION"


    Join Date
    Feb 2012
    Location
    near ATL
    Posts
    36
    Rep Power
    25

    Re: KONICA 7022 Showing "PLEASE ADJUST L DETECTION"

    Toner Density sensor issue. Either too much or too littler toner in the developer. Have you swapped in a developer unit from a different machine? That will cause this error. Only fix in that case is to replace developer and run L-Detect again. Check to make sure machine is adding toner to the developer. Could be a bad Toner Density sensor. What was the given L-Detect value after you ran L-Detect?

  5. #5
    Trusted Tech 50+ Posts
    Join Date
    Oct 2011
    Posts
    72
    Rep Power
    26

    Re: KONICA 7022 Showing "PLEASE ADJUST L DETECTION"

    hI mr. mcbig,
    The value of the Ldetectiom is only 83 and the result is 6, maybe the cause of this one is the developer?
    Many thanks again,
    Cesar

  6. #6
    Service Manager 5,000+ Posts
    KONICA 7022 Showing "PLEASE ADJUST L DETECTION"


    Join Date
    Jan 2006
    Location
    Las Vegas, NV
    Posts
    9,940
    Rep Power
    153

    Lightbulb Re: KONICA 7022 Showing "PLEASE ADJUST L DETECTION"

    This Parts & Service Manual can now be purchased for $12.77 and downloaded immediately after payment from

    Just Manuals ~ The Internet's largest selection of manuals ~ Instant Downloads

    Paul@justmanuals.com

  7. #7
    Technician
    KONICA 7022 Showing "PLEASE ADJUST L DETECTION"


    Join Date
    Feb 2012
    Location
    near ATL
    Posts
    36
    Rep Power
    25

    Re: KONICA 7022 Showing "PLEASE ADJUST L DETECTION"

    When I run into this situation, the developer unit is usually not original to the machine... as in taken from another machine. You will have to change the developer unless you have the original unit. The other cause for this is why I asked the questions above that you did not answer. If a total memory clear has been done on this machine, it can cause issues, although I have been able to get it to setup again.

    Change the developer.


    Quote Originally Posted by legaspiclg View Post
    hI mr. mcbig,
    The value of the Ldetectiom is only 83 and the result is 6, maybe the cause of this one is the developer?
    Many thanks again,
    Cesar

  8. #8
    Trusted Tech 50+ Posts
    Join Date
    Oct 2011
    Posts
    72
    Rep Power
    26

    Re: KONICA 7022 Showing "PLEASE ADJUST L DETECTION"

    Hi Mr. Big.
    Thank you very much for the advice, I will buy a developer.
    Regards,

  9. #9
    mattf
    Guest

    Re: KONICA 7022 Showing "PLEASE ADJUST L DETECTION"

    Quote Originally Posted by MCBIG View Post
    When I run into this situation, the developer unit is usually not original to the machine... as in taken from another machine. You will have to change the developer unless you have the original unit. The other cause for this is why I asked the questions above that you did not answer. If a total memory clear has been done on this machine, it can cause issues, although I have been able to get it to setup again.

    Change the developer.
    Hi maybe you can help me. I did do a total memory clear on a 7135 and I now get this message on the screen. I was wondering if you might be able to help me on how to get it to setup again?

    Thank You!

    Matt
    Last edited by mattf; 08-23-2013 at 08:40 PM.

  10. #10
    Senior Tech 100+ Posts kmcopytech's Avatar
    Join Date
    Dec 2007
    Location
    DongGuan
    Posts
    141
    Rep Power
    35

    Re: KONICA 7022 Showing "PLEASE ADJUST L DETECTION"

    Run L Detect.into 36 mode!

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here