Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 8 of 8
  1. #1
    Field Supervisor 500+ Posts
    Join Date
    Jun 2010
    Location
    folsom
    Posts
    519
    Rep Power
    33

    Konica bizhub c-252 c-5102/3 code

    Hello,
    My c252 is getting a c-5102 and in the service it gives me a c-5102/3, I'm not sure what that means! a 5102 I believe is a main motor issue, I know there are several motors is in that area. Is that the motor that drives the transfer assembly and black drum unit ? I trouble reset the code and sometimes I can get the machine to come to ready and run a few copies then it will error out. I also turned the black drum it seem to be fine but I did not turn the developer roller, I dont think that matters and I turned the main motor by hand there does not seem to be any binding and I can see the transfer assembly rotate. I also removed the transfer assembly and turned it by hand, not binding. When I do a trouble reset and reboot the motor just sits there then the machine errors. thanks
    Last edited by acsolutions; 09-07-2012 at 02:20 AM.

  2. #2
    Junior Member
    Join Date
    Apr 2012
    Location
    Heilbronn
    Posts
    6
    Rep Power
    0

    Re: Konica bizhub c-252 c-5102/3 code

    Good morning!
    There are 3 Motors in the Bizhubc252(M1-M3) M1 and M3 are same!
    exchange, nevertheless, the both! and you see whether your mistake walks.
    If so then the motor is defective.
    If not the PWB is defective!
    Good Luck!

  3. #3
    Field Supervisor 500+ Posts
    Konica bizhub c-252 c-5102/3 code

    minimerlin's Avatar
    Join Date
    Nov 2007
    Location
    Scottish Highlands
    Posts
    851
    Rep Power
    44

    Re: Konica bizhub c-252 c-5102/3 code

    Quote Originally Posted by acsolutions View Post
    Hello,
    My c252 is getting a c-5102 and in the service it gives me a c-5102/3, I'm not sure what that means! a 5102 I believe is a main motor issue, I know there are several motors is in that area. Is that the motor that drives the transfer assembly and black drum unit ? I trouble reset the code and sometimes I can get the machine to come to ready and run a few copies then it will error out. I also turned the black drum it seem to be fine but I did not turn the developer roller, I dont think that matters and I turned the main motor by hand there does not seem to be any binding and I can see the transfer assembly rotate. I also removed the transfer assembly and turned it by hand, not binding. When I do a trouble reset and reboot the motor just sits there then the machine errors. thanks
    Commen problem with this box, replace the main drive motor..the one on the left looking into the back of the machine!

  4. #4
    Service Manager 5,000+ Posts
    Konica bizhub c-252 c-5102/3 code


    Join Date
    Jan 2006
    Location
    Las Vegas, NV
    Posts
    9,940
    Rep Power
    153

    Lightbulb Re: Konica bizhub c-252 c-5102/3 code

    This Parts & Service Manual can now be purchased for $12.77 and downloaded immediately after payment from


    Just Manuals, The Internet's largest selection of manuals ~ Instant Downloads


    Paul@justmanuals.com

  5. #5
    Field Supervisor 500+ Posts
    Join Date
    Jun 2010
    Location
    folsom
    Posts
    519
    Rep Power
    33

    Re: Konica bizhub c-252 c-5102/3 code

    Quote Originally Posted by minimerlin View Post
    Commen problem with this box, replace the main drive motor..the one on the left looking into the back of the machine!
    Thanks for the response, I just want to know what that /3 is after the 5102, and what board drives it!

  6. #6
    Vulcan Inventor of Death 1,000+ Posts Mr Spock's Avatar
    Join Date
    Aug 2006
    Location
    tampa,fl
    Posts
    2,067
    Rep Power
    63

    Re: Konica bizhub c-252 c-5102/3 code

    whenever KM uses a slash with a code 5102/3 that means the code can either be 5102 or 5103 for the troubleshooting info.
    And Star Trek was just a tv show...yeah right!

  7. #7
    Senior Tech 100+ Posts PeterG's Avatar
    Join Date
    Jul 2008
    Location
    Bendigo
    Posts
    177
    Rep Power
    33

    Re: Konica bizhub c-252 c-5102/3 code

    I believe I can change a C-250/252 main motor with my eyes closed now. Very common problem.
    Now takes me about 40 minutes from "walk in" to "walk out'.

  8. #8
    Field Supervisor 500+ Posts
    Join Date
    Jun 2010
    Location
    folsom
    Posts
    519
    Rep Power
    33

    Re: Konica bizhub c-252 c-5102/3 code

    Ribbon cable!

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here