Page 4 of 5 FirstFirst 12345 LastLast
Results 31 to 40 of 42

Thread: C554 J2002

  1. #31
    Junior Member MJabbar's Avatar
    Join Date
    Apr 2015
    Location
    Hamtramck, MI
    Posts
    2
    Rep Power
    0

    Re: C554 J2002

    Quote Originally Posted by Spidula View Post
    This customer was using 80g but is really cheap sh*t.
    This is really helpful thank you.

  2. #32
    RTFM!! 5,000+ Posts allan's Avatar
    Join Date
    Apr 2010
    Location
    Centurion
    Posts
    5,387
    Rep Power
    152

    Re: C554 J2002

    Really. Its driving me nuts on one machine. More than 500K on the machine and then it would happen mysteriously.
    Having this problem on tray 1 and tray 2. Bypass would feed an entire ream continuously with no problem.

    So i will try the springs and the dip switch.

    This one gives J9901 and J2002 every 150 pages on standard good quality 80gsm A4. Making me waste Friday afternoons in frustration.

    Fixed J2002 on one machine by adding shims to the inside of the door hooks. Never had a jam again.
    Fixed one with J9901 by removing and reinstalling the door. Also no more jams.

    This is silly. Seems to be a combo @#*$ of different solutions for a stupid problem.
    Then its just a couple of these problem children. All the others are rocking on with no problem.
    Whatever

  3. #33
    Senior Tech 100+ Posts andyf424's Avatar
    Join Date
    Jun 2013
    Location
    Milwaukee
    Posts
    126
    Rep Power
    24

    Re: C554 J2002

    I've got one doing it now, have we come to a consensus on what the "best" fix is?

  4. #34
    Service Manager 1,000+ Posts
    Join Date
    Apr 2009
    Location
    LaPorte Indiana
    Posts
    1,054
    Rep Power
    43

    Re: C554 J2002

    We have 1 BH554e doing this to us!! No 99-01's but getting 20-02 jams quite often. Paper comes out of tray 2 about 4 inches and JAM. We clean that out and away it runs. We saw that the door
    appears warped on this one machine, but it is all Plastic. Shimming latch did tighten it up. We have done New feed section and tray 2 feed motor assembly on back. No help from KonMin on this one.

  5. #35
    Field Supervisor 500+ Posts
    Join Date
    Jan 2009
    Location
    UK
    Posts
    826
    Rep Power
    50

    Re: C554 J2002

    Quote Originally Posted by mo0651 View Post
    We have 1 BH554e doing this to us!! No 99-01's but getting 20-02 jams quite often. Paper comes out of tray 2 about 4 inches and JAM. We clean that out and away it runs. We saw that the door
    appears warped on this one machine, but it is all Plastic. Shimming latch did tighten it up. We have done New feed section and tray 2 feed motor assembly on back. No help from KonMin on this one.
    So we can assume you have fitted the low tension spring to the tray, fitted the modified conveyance roller and the modified pulling springs on the side door?
    These are all official mods from KM and they do work.

  6. #36
    Service Manager 1,000+ Posts
    Join Date
    Apr 2009
    Location
    LaPorte Indiana
    Posts
    1,054
    Rep Power
    43

    Re: C554 J2002

    The only bulletins we have seen state "when feeding from the LCC" PC410. That is not in play. Only tray 2.

  7. #37
    Senior Tech 250+ Posts
    Join Date
    Oct 2014
    Location
    wareham.mass
    Posts
    343
    Rep Power
    23

    Re: C554 J2002

    Quote Originally Posted by mo0651 View Post
    The only bulletins we have seen state "when feeding from the LCC" PC410. That is not in play. Only tray 2.
    Say any fix for this I am having same problem!

    Sent from my SM-N920V using Tapatalk

  8. #38
    Service Manager 1,000+ Posts
    C554 J2002

    habik's Avatar
    Join Date
    Apr 2010
    Posts
    2,015
    Rep Power
    59

    Re: C554 J2002

    Quote Originally Posted by antone View Post
    Say any fix for this I am having same problem!

    Sent from my SM-N920V using Tapatalk
    Drive roller new ribbed black.
    Softer pick spring.
    Separation torque limiter likes to seize up.
    Feed sensor are better wiped than just blown.
    Lubricating feed shafts bushings does improve feeding.
    There is foam padded guide on T2 which can be obstructive, remove it along with the self adhesive tape.
    If you have T3 LCT the amount of paper being fed throughout vertical tend wear out the mylar on T2 and causing it to curve on the edge inwards the tray 2 causing 2002s.
    Depending on paper registration loop adjustments do some magic as well!
    Registration rollers can slow down if bushings are not cleaned.
    Registration actuator does wear as well. I change it around 1 mil on most machines.
    Presume you are using Grey ribbed pick rollers and have the latest firmware on machine.


    Sent from my Mi A1 using Tapatalk
    .OK Google! ... will I need Berrocca this morning?
    Firmwares HERE

  9. #39
    Service Manager 1,000+ Posts
    C554 J2002

    habik's Avatar
    Join Date
    Apr 2010
    Posts
    2,015
    Rep Power
    59

    Re: C554 J2002

    Forgot to add.

    If T3&4 are used there is one way spring clutch which has to have washer and then c-clip.
    They like to seize and when cleaning vertical rollers roll the rolls in feed direction as if you turn the other way the spring may come out of position inside the clutch.

    Hope this helps!

    Sent from my Mi A1 using Tapatalk
    .OK Google! ... will I need Berrocca this morning?
    Firmwares HERE

  10. #40
    Junior Member
    Join Date
    Feb 2018
    Location
    Royal Oak, MI
    Posts
    1
    Rep Power
    0

    Re: C554 J2002

    Quote Originally Posted by Spidula View Post
    Update for any of you guys interested on this one.

    There is now a tech bulletin out for KONICA MINOLTA AUTHORISED TECHNICAL PERSONNEL. Regarding this problem. You should be able to get it on Infohub.

    There is a spare spring mounted on the full feed assy to swap over with the problem tray. Did this today and ran 500+ through tray two with not one jam!

    Happy Days

    Good Night!

    This has worked every time I've tried it!!!

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here