Thanks Thanks:  0
Dislikes Dislikes:  0
Results 1 to 9 of 9
  1. #1
    Technician Bizhub350's Avatar
    Join Date
    Oct 2013
    Location
    Manila
    Posts
    11
    Rep Power
    22

    Pls. help on Bizhub 350 output copy is a little oblique/slanted...how to fix?

    Guys please need help on how to fix Bizhub 350 output copy is a little oblique or slanted...thank you
    output copy.jpg

  2. #2
    ALIEN OVERLORD 2,500+ Posts fixthecopier's Avatar
    Join Date
    Apr 2008
    Location
    The Republic of Pineland
    Posts
    4,716
    Rep Power
    134

    Re: Pls. help on Bizhub 350 output copy is a little oblique/slanted...how to fix?

    You take the cover off the front side of elevator, or output tray, and you pull off the gear and belt and put in correct position and reassemble.
    The greatest enemy of knowledge isn't ignorance, it is the illusion of knowledge. Stephen Hawking

  3. #3
    Service Manager 5,000+ Posts
    Pls. help on Bizhub 350 output copy is a little oblique/slanted...how to fix?


    Join Date
    Jan 2006
    Location
    Las Vegas, NV
    Posts
    9,940
    Rep Power
    153

    Lightbulb Re: Pls. help on Bizhub 350 output copy is a little oblique/slanted...how to fix?

    This Parts & Service manual can now be purchased for $12.77 and downloaded immediately after payment from:


    Just Manuals, The Internet's largest selection of manuals ~ Instant Downloads


    Paul@justmanuals.com

  4. #4
    Master Of The Obvious 10,000+ Posts
    Pls. help on Bizhub 350 output copy is a little oblique/slanted...how to fix?

    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    22,445
    Rep Power
    462

    Re: Pls. help on Bizhub 350 output copy is a little oblique/slanted...how to fix?

    So ... is it an optical skew from a print, an optical skew from a copy, or a paper skew? =^..^=
    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.
    3) if you're going to ask about jams include the jam code.
    4) if you're going to ask about an error code include the error code.
    5) You are the person onsite. Only you can make observations.

    blackcat: Master Of The Obvious =^..^=

  5. #5
    Senior Tech 250+ Posts
    Join Date
    Nov 2011
    Location
    Jacksonville, Fl
    Posts
    388
    Rep Power
    33

    Re: Pls. help on Bizhub 350 output copy is a little oblique/slanted...how to fix?


    THIS IS YOUR FIX...
    Remove glass and use a hex wrench (maybe 1.5mm? or 1.27?) on front and/or rear black hex screws that have threadlock on them in the CCD/lens box. Twist 1/4 turn cw or ccw and note the change. test, correct as needed. If you go too far, you will see black ribs on edges. Anytime these are rolled around and strongly vibrated, we notice optic skew, even when adjusted correctly, then delivered to customer a bounce on the sidewalk or worse yet, concrete with cobblestone is sure to do it, so be careful when moving! This is a standard part of our refurb process.

  6. #6
    Technician Bizhub350's Avatar
    Join Date
    Oct 2013
    Location
    Manila
    Posts
    11
    Rep Power
    22

    Re: Pls. help on Bizhub 350 output copy is a little oblique/slanted...how to fix?

    it is a skew from a print out but my original is perfectly fine...and I notice if I do a tests pattern copy the turn out is fine and not skew...only when i copy a fine one the output is skew... thanks for all your help guys

  7. #7
    Service Manager 2,500+ Posts
    Pls. help on Bizhub 350 output copy is a little oblique/slanted...how to fix?

    Hansoon's Avatar
    Join Date
    Sep 2007
    Posts
    3,190
    Rep Power
    94

    Re: Pls. help on Bizhub 350 output copy is a little oblique/slanted...how to fix?

    Yank up the left front corner of the scanner unit. Somebody was leaning on it and it went down a little.

    This is the most common cause of skewing in the copy mode by all machines of this design starting with the Di-350 through Di-351, Di-3510 series until the BH-350's and likely also the BH-362 series.

    Hans
    " Sent from my Intel 80286 using MS-DOS 2.0 "

  8. #8
    Technician Bizhub350's Avatar
    Join Date
    Oct 2013
    Location
    Manila
    Posts
    11
    Rep Power
    22

    Re: Pls. help on Bizhub 350 output copy is a little oblique/slanted...how to fix?

    Hansoon tnx it really works Yanking up the left front corner of the scanner unit, now the output copy is A okey no more skew tnx again...your the man...

  9. #9
    Service Manager 2,500+ Posts
    Pls. help on Bizhub 350 output copy is a little oblique/slanted...how to fix?

    Hansoon's Avatar
    Join Date
    Sep 2007
    Posts
    3,190
    Rep Power
    94

    Re: Pls. help on Bizhub 350 output copy is a little oblique/slanted...how to fix?

    Glad you solved it and thanks for the feed back.

    Hans
    " Sent from my Intel 80286 using MS-DOS 2.0 "

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here