Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 7 of 7
  1. #1
    Technician
    Join Date
    Apr 2010
    Posts
    40
    Rep Power
    29

    KM Bizhub C652 hangs up

    HI

    I have a problem with Bizhub C652 copier hp. It is the time of the controller IC-412. From time to time crashes, one print comes out, and the rest is in the print queue and printer status 'offline'. When I turn off the copier and I turn on again, the rest of the print from queue prints. And one more thing, for example, to print the configuration of the controller, the bizhub has the IP address 192.168.5.44 and 192.168.5.45 machine. After entering the IP controller shows the controller configuration page, and after entering the IP machines to the shows page with the configuration of the controller. A should be the side of the device configuration (setting scans, etc.) Please help me how to fix it.

  2. #2
    Technician a4o7910's Avatar
    Join Date
    Jul 2013
    Location
    montana
    Posts
    28
    Rep Power
    0
    Set ic412 factory default setting.

  3. #3
    Technician
    Join Date
    Apr 2010
    Posts
    40
    Rep Power
    29

    Re: KM Bizhub C652 hangs up

    I did it. I installed new software to Ic412. And don't help. ;-/

  4. #4
    Vulcan Inventor of Death 1,000+ Posts Mr Spock's Avatar
    Join Date
    Aug 2006
    Location
    tampa,fl
    Posts
    2,067
    Rep Power
    63

    Re: KM Bizhub C652 hangs up

    Do you have one or two cables going to the wall.
    If one then the ip address should start with a 172. ip address.
    Also is the ic set to pull an address for the machine? If so this could be the issue. It pulls the next one higher then the ic for the machine. If the machine has the next higher and the ic has the next higher then 2 machines have the same ip and that will cause print issues.
    And Star Trek was just a tv show...yeah right!

  5. #5
    Technician
    Join Date
    Apr 2010
    Posts
    40
    Rep Power
    29

    Re: KM Bizhub C652 hangs up

    From ic412 goes to machine, and from machine goes to wall.

    Machine have two ip, i checked it from laptop, no machine have the same ip.

  6. #6
    Vulcan Inventor of Death 1,000+ Posts Mr Spock's Avatar
    Join Date
    Aug 2006
    Location
    tampa,fl
    Posts
    2,067
    Rep Power
    63

    Re: KM Bizhub C652 hangs up

    fiery setup.jpg

    see if you can read the attached

    I am not an artist....
    And Star Trek was just a tv show...yeah right!

  7. #7
    Field Supervisor 2,500+ Posts
    Join Date
    Jun 2009
    Posts
    3,009
    Rep Power
    96

    Re: KM Bizhub C652 hangs up

    If your MFP has a static IP of 192.168.x.x, then you should be using the 2 Ethernet line setup, Obtain IP from engine should be off in the controller config. The controller should not have the x-over cable running to the MFP. Emujo
    If you don't see your question answered in the forum, please don't think it's OK to PM me for a personal reply...I do not give out firmware and/or manuals.

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here