Page 3 of 3 FirstFirst 123
Results 21 to 29 of 29
  1. #21
    Service Manager 1,000+ Posts
    Join Date
    Sep 2008
    Location
    Flat Rock Michigan
    Posts
    1,046
    Rep Power
    49

    Re: Konica press 1250 jam 2101

    Quote Originally Posted by blackcat4866 View Post
    The drum claws are new and working properly. I'm disturbed that the jammed paper is not discharged. If the paper does not discharge, there's no way it can pass.

    The HVT on the imaging drawer did not help. I also imported the machine settings from a year ago. At this stage it will not pass a single page of any type of paper. =^..^=
    ensure drum ground path, have seen this kind of thing in may different models, usually ends up being static buildup due to poor grounding.

  2. #22
    RTFM!! 5,000+ Posts allan's Avatar
    Join Date
    Apr 2010
    Location
    Centurion
    Posts
    5,387
    Rep Power
    152

    Re: Konica press 1250 jam 2101

    Found a new reason the machine would give J-2101 that and J-3111(skew sensor jam).
    If tray 1 and 2's feed tires are done it makes a dent in the paper that would catch under the drum.
    Had that jam while i was working on a machine next to it it would jam every 100 pages or so.
    Changed the feed tires and the problem was gone more than 10000 pages printed!
    Whatever

  3. #23
    Master Of The Obvious 10,000+ Posts
    Konica press 1250 jam 2101

    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    22,445
    Rep Power
    462

    Re: Konica press 1250 jam 2101

    Quote Originally Posted by allan View Post
    Found a new reason the machine would give J-2101 that and J-3111(skew sensor jam).
    If tray 1 and 2's feed tires are done it makes a dent in the paper that would catch under the drum.
    Had that jam while i was working on a machine next to it it would jam every 100 pages or so.
    Changed the feed tires and the problem was gone more than 10000 pages printed!
    What kind of usable life do you get from the standard rollers? The stated yield is 500K, but about 300K is about all I can expect. The orange neoprene rollers seem to wear more slowly. The problem is that there are more jams, even when brand new. I won't be installing any more of the orange rollers. And if you add the pickup weights you'll get less than 200K, and the rollers wear unevenly.

    Thanks for the information. =^..^=
    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.
    3) if you're going to ask about jams include the jam code.
    4) if you're going to ask about an error code include the error code.
    5) You are the person onsite. Only you can make observations.

    blackcat: Master Of The Obvious =^..^=

  4. #24
    RTFM!! 5,000+ Posts allan's Avatar
    Join Date
    Apr 2010
    Location
    Centurion
    Posts
    5,387
    Rep Power
    152

    Re: Konica press 1250 jam 2101

    Those big grey ones? A4EUR714## ?

    Got more than the yield. 500K + that assembly does feel a bit flimsy?
    I changed them on a total page count of 12M and a feed count of 8M for the first time.
    Have to say the wear looked minimal and even. I compared the old ones to the new ones while changing them out.
    Every thing one these machines goes well past.
    Got the air suction feed units on there PF-703 that thing is rock solid, so tray 1 and 2 shares only a little of the load.

    The orange ones would do about 250K from my experience the ones on the B423?
    I always change all 3 at the same time but its then only the separation roller that was badly worn out.
    Those grey ribbed pick up tires works really well i leave them on there for a second time.

    The B601 machine roller would do 250K+.
    Whatever

  5. #25
    Technician
    Join Date
    Jul 2016
    Location
    North Little Rock
    Posts
    15
    Rep Power
    16

    Re: Konica press 1250 jam 2101

    Quote Originally Posted by mx6turbo89 View Post
    I have had this problem with several different boxes and every time it has been the transfer offset adjustment that has fixed it. It can be adjusted per tray:

    J-2101
    [Symptom]Drum wrapping jam occurs when using specific paper.
    [Cause]Transfer value and transfer timing is inappropriate.
    [Solution]Change the transfer current value in the MACHINE screen as follows. (Transfer leading edge 1, 2 only)[Tray Setting]-[Change Set]-[Process Adj.]-[Transfer Offset Adj.]Step1Increase offset value at leading edge1. (by 10 step)*: When belt separation and leading edge image quality were deteriorated, decrease the value.Step2 (If Step1 is not effective)Decrease the value of the leading edge1 and 2.*: When the transfer fails at the leading edge section, increase the value.Then, register the name of the paper. (Can be register up to 100)

    Ok, I am going to give this a try. We have changed transfer voltage for the tray already and adjusted the solenoid position at the same time about 6 weeks ago. It runs well and then occasionally (sometimes after thousands of copies) it will do it again. And it only does it on 8 1/2 x 11 paper. Any larger sizes and it works perfectly. I am guessing the extra weight from the longer sheet is enough to pull it off the drum. Whatever is wrong is just barely wrong. I'll post the results of this. Feels like KMinolta should address this a little better.

  6. #26
    Technician
    Join Date
    Jul 2016
    Location
    North Little Rock
    Posts
    15
    Rep Power
    16

    Re: Konica press 1250 jam 2101

    Quote Originally Posted by jaredfmn View Post
    We have several 1250 and 1200 machines in the field jamming with 2101 jam codes. I have gone through the trouble shooting guide with little luck. Tried new transfer unit and cleaning unit. Full pms on all the machines with new drums and developer. If anybody has any ideas I am open to suggestions. They have the latest and greatest firmware as well.

    If you have access to the Konica site there is a Troubleshooting guide accessible on the SSD page that was released in July. It has several suggestions for dealing with a J-2101. Many have been mentioned here already but it is worth looking at.

  7. #27
    Senior Tech 100+ Posts
    Konica press 1250 jam 2101

    mx6turbo89's Avatar
    Join Date
    Oct 2013
    Posts
    154
    Rep Power
    27

    Re: Konica press 1250 jam 2101

    Quote Originally Posted by cgw71 View Post
    Ok, I am going to give this a try. We have changed transfer voltage for the tray already and adjusted the solenoid position at the same time about 6 weeks ago. It runs well and then occasionally (sometimes after thousands of copies) it will do it again. And it only does it on 8 1/2 x 11 paper. Any larger sizes and it works perfectly. I am guessing the extra weight from the longer sheet is enough to pull it off the drum. Whatever is wrong is just barely wrong. I'll post the results of this. Feels like KMinolta should address this a little better.
    KM does have a lot of write-ups for this problem. This guide has been helpful for me (particularly the last page): https://www.dropbox.com/s/tn7v8wcm45...ollow.pdf?dl=0

  8. #28
    Junior Member
    Join Date
    May 2009
    Location
    Baltimore, MD
    Posts
    7
    Rep Power
    0

    Re: Konica press 1250 jam 2101

    Quote Originally Posted by mx6turbo89 View Post
    I have had this problem with several different boxes and every time it has been the transfer offset adjustment that has fixed it. It can be adjusted per tray:

    J-2101
    [Symptom]Drum wrapping jam occurs when using specific paper.
    [Cause]Transfer value and transfer timing is inappropriate.
    [Solution]Change the transfer current value in the MACHINE screen as follows. (Transfer leading edge 1, 2 only)[Tray Setting]-[Change Set]-[Process Adj.]-[Transfer Offset Adj.]Step1Increase offset value at leading edge1. (by 10 step)*: When belt separation and leading edge image quality were deteriorated, decrease the value.Step2 (If Step1 is not effective)Decrease the value of the leading edge1 and 2.*: When the transfer fails at the leading edge section, increase the value.Then, register the name of the paper. (Can be register up to 100)

    I am also having these issues with a 1052 and I believe these adjustments will work, but the problem I have is that all of my high voltage adjustments are grayed out. Does anyone know where to turn them on? I'm sure it is a DIPSW, but I don't have time to look at every one until I find it.

  9. #29
    Self Employed 1,000+ Posts D_L_P's Avatar
    Join Date
    Oct 2009
    Location
    Canton, Ohio
    Posts
    1,196
    Rep Power
    53

    Re: Konica press 1250 jam 2101

    Just throwing this out there but HV is modified by the machine depending on humidity. Check or replace the sensors if they report 0% humidity. IIRC the 950 had a thermistor below the transfer/sep unit. Replacing that thermistor fixed some weird cq/codes. It's a shot in the dark but maybe due to that sensor the machine thinks it has to lower the separation voltage.

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here