Thanks Thanks:  0
Dislikes Dislikes:  0
Page 1 of 3 123 LastLast
Results 1 to 10 of 28
  1. #1
    Technician Wasfil's Avatar
    Join Date
    May 2008
    Location
    Jakarta
    Posts
    20
    Rep Power
    20

    Thumbs down Bizhub 600 Always warming Up

    Bz600, after I do Copy and hushed 1minute or more, lather than The machine canot use, at screen come up this Message "Please wait Warming up the machine" Before that always eror code C2803 & 2804, My counter is 300.000

    Last edited by Aneurysm; 05-17-2008 at 11:56 PM.

  2. #2
    ALIEN OVERLORD 2,500+ Posts fixthecopier's Avatar
    Join Date
    Apr 2008
    Location
    The Republic of Pineland
    Posts
    4,424
    Rep Power
    114
    On other models of Konica Minolta, when he machine keeps warming up, it is looking for toner to complete the job. If the bottle has toner, and conditions are humid, you may have to clean out the hopper under the bottle holder.The toner could stick together around the auger, not allowing it to feed into the DV box.


  3. #3
    Technician Wasfil's Avatar
    Join Date
    May 2008
    Location
    Jakarta
    Posts
    20
    Rep Power
    20

    Question

    Thanks, but that to long time and canot be use until I tur OF and Turn On again. And That problem always happened every day.


  4. #4
    Senior Tech 250+ Posts ck1's Avatar
    Join Date
    Apr 2008
    Posts
    432
    Rep Power
    24
    just follow fixthecopier said, check the thing .


  5. #5
    Senior Tech 100+ Posts
    Join Date
    Aug 2007
    Posts
    151
    Rep Power
    22
    At 300,000 hope you have replaced drum, starter, blade etc. Best to do this at correct time, 250,000, or problems will come your way.


  6. #6
    Curmudgeon at large 100+ Posts RockETop's Avatar
    Join Date
    Apr 2007
    Location
    Colorado
    Posts
    172
    Rep Power
    23
    I have a machine with over 1M copies that just started this today. I'll let you know what happens. RET


    Edit: after a little research, I vote TCSB. I had already cleaned out the process unit. I'll hose out the toner supply unit tomorrow first....cheaper!

    Last edited by RockETop; 05-16-2008 at 03:40 AM.

  7. #7
    Technician
    Join Date
    Apr 2008
    Location
    nsw
    Posts
    24
    Rep Power
    20
    Quote Originally Posted by Downunder View Post
    At 300,000 hope you have replaced drum, starter, blade etc. Best to do this at correct time, 250,000, or problems will come your way.
    I would do the above first. I have also had a faulty Dmax sensor cause this problem also. Make sure the sensor is very clean. If you check the service code counter you may see a few dmax errors listed..


  8. #8
    Curmudgeon at large 100+ Posts RockETop's Avatar
    Join Date
    Apr 2007
    Location
    Colorado
    Posts
    172
    Rep Power
    23
    TCSB! Went right to work.

    Run drum peculiarity. you may get errors.


  9. #9
    Technician Wasfil's Avatar
    Join Date
    May 2008
    Location
    Jakarta
    Posts
    20
    Rep Power
    20

    Exclamation PC Drum is be Replaced

    PC Drum, Starter tobe replace before, but the problem has be come after amoment (1minute) I do copy once in the screen "Warming Up Ready to Scan" I can do Scan, but the result print not going out.

    I have do : Drum Peculiarity - Auto MAx. Density Adj the result is Ok, then Auto gamma Adjst. (1dot) and (2dot) the result is Error 1, in the book that mean TCSB dirt,

    In other machine i have change/replace with New TCSB the problem is lose. (Ihave 2 machine with same problem)

    Thanks alot for All guys.....


  10. #10
    Trusted Tech 50+ Posts
    Join Date
    Feb 2008
    Location
    Halifax, Nova Scotia
    Posts
    69
    Rep Power
    20
    It may sound kind of strange, but I had one of these machines that would go to warm up and not come out unless the power was reset. I checked everything and all seemed ok. With nothing left to do, I flashed the machine. It already had the latest firmware, but I did this anyway. It's been months now, and the problem has not came back.


Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •