Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 7 of 7
  1. #1
    Technician
    Join Date
    Sep 2012
    Location
    lahore
    Posts
    24
    Rep Power
    24

    km 6030 image cycle problem

    Image cycle appear again and again,i have cleaned developer tank and toner sensor again ang again,but image cycle appear after every 20 to 30 copies,and developer tank is full of toner

  2. #2
    Field Supervisor 500+ Posts
    km 6030 image cycle problem


    Join Date
    May 2009
    Location
    Concord, NH
    Posts
    770
    Rep Power
    53

    Re: km 6030 image cycle problem

    Check/replace the duplex PWB. Sometimes toner dusting will cause the board to provide erroneous readings and cleaning it will correct the problem. But in most of the cases we have run up against replacing the board has solved this problem. It is a relatively small board located at the RH rear side of the machine, a note of caution when removing/re-installing the PWB do not over tighten the screws, the board is easily cracked and hence made unusable. Hope this helps.

  3. #3
    Master Of The Obvious 10,000+ Posts
    km 6030 image cycle problem

    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    22,442
    Rep Power
    462

    Re: km 6030 image cycle problem

    Quote Originally Posted by umer_ml View Post
    Image cycle appear again and again,i have cleaned developer tank and toner sensor again ang again,but image cycle appear after every 20 to 30 copies,and developer tank is full of toner
    Is the developing unit completely full of toner to the top? =^..^=
    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.
    3) if you're going to ask about jams include the jam code.
    4) if you're going to ask about an error code include the error code.
    5) You are the person onsite. Only you can make observations.

    blackcat: Master Of The Obvious =^..^=

  4. #4
    Technician
    Join Date
    Sep 2012
    Location
    lahore
    Posts
    24
    Rep Power
    24

    Re: km 6030 image cycle problem

    Yes completely full of toner! and toner leak out of developer tank cover

  5. #5
    Master Of The Obvious 10,000+ Posts
    km 6030 image cycle problem

    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    22,442
    Rep Power
    462

    Re: km 6030 image cycle problem

    I can think of one possibility:

    1) perhaps one of the developing unit contacts is not making a good connection. On this model the level in the toner hopper is measured by an antenna contact in the developing unit, which measures how much of the developer bias current is being conducted through the toner. If developer bias is absent or the antenna disconnected, the developing unit will not detect full, and continue adding toner.
    =^..^=
    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.
    3) if you're going to ask about jams include the jam code.
    4) if you're going to ask about an error code include the error code.
    5) You are the person onsite. Only you can make observations.

    blackcat: Master Of The Obvious =^..^=

  6. #6
    Senior Tech 100+ Posts
    km 6030 image cycle problem


    Join Date
    Sep 2011
    Posts
    225
    Rep Power
    31

    Re: km 6030 image cycle problem

    Quote Originally Posted by Santander View Post
    Check/replace the duplex PWB. Sometimes toner dusting will cause the board to provide erroneous readings and cleaning it will correct the problem. But in most of the cases we have run up against replacing the board has solved this problem. It is a relatively small board located at the RH rear side of the machine, a note of caution when removing/re-installing the PWB do not over tighten the screws, the board is easily cracked and hence made unusable. Hope this helps.
    I've the toner add had mechanism go bad, if I remember, it ws plastic tan, on the side of a gear was found broken off. So toner never gets to actually add toner. I doret if ist
    part of the toner otr or not. comes out preety easy to access motor/and or toner add gear/drive assem.
    good luck mate

  7. #7
    IT Manager 10,000+ Posts bsm2's Avatar
    Join Date
    Feb 2008
    Location
    Biden 2024
    Posts
    25,755
    Rep Power
    333

    Re: km 6030 image cycle problem

    clean all the filters in the back of the machine, I know weird but its some kind of temperature thing

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here