Page 1 of 2 12 LastLast
Results 1 to 10 of 12
  1. #1
    Technician
    Join Date
    Apr 2016
    Location
    Ardmore, OK
    Posts
    21
    Rep Power
    17

    Question 0533 Out of Tray 3 only (4551ci w/ PF-740)

    Fighting a battle here with a TA-4551ci with a PF-740. We are getting a Jam 0533. It only jams when using tray 3, tray 4 works just fine. Here's the weird part. We swapped to a known working PF-740 and get the same jam. We replaced the conveying unit and same thing. All electrical connections check out. Any advice is appreciated!

  2. #2
    Service Manager 1,000+ Posts
    0533 Out of Tray 3 only (4551ci w/ PF-740)

    habik's Avatar
    Join Date
    Apr 2010
    Posts
    2,015
    Rep Power
    59

    Re: 0533 Out of Tray 3 only (4551ci w/ PF-740)

    Have you tried firmware re-load?

    Byting on bits.
    .OK Google! ... will I need Berrocca this morning?
    Firmwares HERE

  3. #3
    Technician
    Join Date
    Apr 2016
    Location
    Ardmore, OK
    Posts
    21
    Rep Power
    17

    Re: 0533 Out of Tray 3 only (4551ci w/ PF-740)

    Yep. Updated this morning.

  4. #4
    Senior Tech 100+ Posts
    Join Date
    Jul 2014
    Posts
    188
    Rep Power
    22

    Re: 0533 Out of Tray 3 only (4551ci w/ PF-740)

    I would check for a pinched or uninsulated wire since control and voltage for PFFS1 is on the PF main PWB. And since you swapped the whole feeder (and therefore the PWB), obviously you shouldn't be looking at an issue with the PWB, sensor, clutch, etc. Also check your connector at the engine PWB YC19.

    edit: I see you said that you checked connections but something doesn't add up. Double check!

  5. #5
    Trusted Tech 50+ Posts copygirl's Avatar
    Join Date
    Apr 2008
    Location
    Mobile, Al
    Posts
    75
    Rep Power
    33

    Re: 0533 Out of Tray 3 only (4551ci w/ PF-740)

    Have you taken the paper feed section out and checked it? Am sure you have. It's the new style right? You might wanna try to adjust the retard pulley position. We've had a few that we've had to change the complete feed section out. Oh, and I know this is absurd so forgive me for asking such a simple thing. You did check the stack in the deck to make sure all paper was lined up and not folded up edges? What's the meter reading?
    Ginger

  6. #6
    Technician
    Join Date
    Apr 2016
    Location
    Ardmore, OK
    Posts
    21
    Rep Power
    17

    Re: 0533 Out of Tray 3 only (4551ci w/ PF-740)

    Yes traced all connections from YC19 and resistance was good through all. Also tested for short to ground. The paper stops at the feed assembly right before reaching the mid roller. Right at sensor PFPCS1. Hoping to have our regional Kyocera guru out next week to check it out.

  7. #7
    Technician
    Join Date
    Apr 2016
    Location
    Ardmore, OK
    Posts
    21
    Rep Power
    17

    Re: 0533 Out of Tray 3 only (4551ci w/ PF-740)

    Again, we can swap the PF-740 to another machine and it works fine, so we have eliminated the PF as a culprit.

  8. #8
    Owner/Service Manager 1,000+ Posts
    0533 Out of Tray 3 only (4551ci w/ PF-740)

    tmaged's Avatar
    Join Date
    Oct 2008
    Location
    Center of my Universe
    Posts
    1,759
    Rep Power
    60

    Re: 0533 Out of Tray 3 only (4551ci w/ PF-740)

    Hope that helps !
    -Tony


    www.dtios.com
    Become a fan on Facebook

  9. #9
    Field Supervisor 500+ Posts
    0533 Out of Tray 3 only (4551ci w/ PF-740)


    Join Date
    Oct 2010
    Posts
    815
    Rep Power
    45

    Re: 0533 Out of Tray 3 only (4551ci w/ PF-740)

    Press on the lower door ... the one between the feed cabinet and the transfer section ... during feeds and see if it runs ok. If so the door may be slightly warped outward. I've replaced a couple with the same symptom. Tension from feed section on tray three can overcome the pull from the transport section between the cabinet and transfer section. From tray 4 the paper has completely left the feed unit and is in the horizontal transport unit which has less tension when the next section takes over transport.

  10. #10
    Technician
    Join Date
    Apr 2016
    Location
    Ardmore, OK
    Posts
    21
    Rep Power
    17

    Re: 0533 Out of Tray 3 only (4551ci w/ PF-740)

    Quote Originally Posted by darry1322 View Post
    Press on the lower door ... the one between the feed cabinet and the transfer section ... during feeds and see if it runs ok. If so the door may be slightly warped outward. I've replaced a couple with the same symptom. Tension from feed section on tray three can overcome the pull from the transport section between the cabinet and transfer section. From tray 4 the paper has completely left the feed unit and is in the horizontal transport unit which has less tension when the next section takes over transport.
    Will try in a little bit, Thanks!

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here