Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 5 of 5
  1. #1
    Technician bayshoreoe's Avatar
    Join Date
    Jun 2015
    Location
    Beachwood, NJ
    Posts
    35
    Rep Power
    6

    Taskalfa 221 c6050

    Have this unit throwing c6050 error. Replaced fuser and still does it. Warms up, comes to ready but throws the code when trying to make a copy or in idle. Wall voltage good. Reseated all connections. Any input greatly appreciated.


  2. #2
    Master Of The Obvious 10,000+ Posts
    Taskalfa 221 c6050

    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    15,405
    Rep Power
    249

    Re: Taskalfa 221 c6050

    How good is the wall power? Did you put your multimeter in the hot - neutral for 10 minutes, or do a power quality analysis? =^..^=

    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.
    3) if you're going to ask about jams include the jam code.
    4) if you're going to ask about an error code include the error code.


    blackcat: Master Of The Obvious =^..^=

  3. #3
    Technician bayshoreoe's Avatar
    Join Date
    Jun 2015
    Location
    Beachwood, NJ
    Posts
    35
    Rep Power
    6

    Re: Taskalfa 221 c6050

    Reading 121 for over 5 minutes. Fuser powers up on start up, but once machine comes to ready, it never turns back on to keep temperature up, just goes into code.

    Brian


  4. #4
    Master Of The Obvious 10,000+ Posts
    Taskalfa 221 c6050

    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    15,405
    Rep Power
    249

    Re: Taskalfa 221 c6050

    121vac hot to neutral? What about ground to neutral? =^..^=

    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.
    3) if you're going to ask about jams include the jam code.
    4) if you're going to ask about an error code include the error code.


    blackcat: Master Of The Obvious =^..^=

  5. #5
    Senior Tech 250+ Posts
    Taskalfa 221 c6050


    Join Date
    May 2009
    Location
    Concord, NH
    Posts
    303
    Rep Power
    24

    Re: Taskalfa 221 c6050

    Quote Originally Posted by bayshoreoe View Post
    Have this unit throwing c6050 error. Replaced fuser and still does it. Warms up, comes to ready but throws the code when trying to make a copy or in idle. Wall voltage good. Reseated all connections. Any input greatly appreciated.
    After replacing the fuser did you run Sim 163 to reset any fuser error codes, just replacing the fuser does not automatically reset the error codes. You could also run Sim 198 [turn on] Phase control to have the unit eliminate electrical noise caused by the surrounding environment and the unit itself. Blackcat is also correct in making sure that the neutral to ground is wired properly. A simple cheap outlet tester will let you know if the outlet is wired correctly. The routing of the wiring is also important, after replacing the fuser did you run the unit with the cover off? Simply putting the cover on with improper wire routing can cause a wire crimp or a dislodging of a connector. Hoe this helps.


Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-=-=-=-=-=-


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here