Thanks Thanks:  0
Dislikes Dislikes:  0
Results 1 to 4 of 4

Thread: TA221 J11

  1. #1
    Senior Tech 100+ Posts blackdog's Avatar
    Join Date
    Jun 2012
    Location
    MA
    Posts
    200
    Rep Power
    13

    TA221 J11

    Hey you Kyocera Aces,
    Got a TA221 giving a J11 Jam code from cassette 1.
    I installed new feed/sep rollers, clutch is working fine.
    Swapped out cassettes and still N/G.
    What bugs me is sep roller is turning but no feed?
    Any suggestions would be greatly appreciated.


  2. #2
    Master Of The Obvious 10,000+ Posts
    TA221 J11

    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    15,216
    Rep Power
    245

    Re: TA221 J11

    Is the separation roller flopping around because, maybe, the plastic post that it swivels on is busted off? =^..^=

    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.
    3) if you're going to ask about jams include the jam code.
    4) if you're going to ask about an error code include the error code.


    blackcat: Master Of The Obvious =^..^=

  3. #3
    Senior Tech 100+ Posts blackdog's Avatar
    Join Date
    Jun 2012
    Location
    MA
    Posts
    200
    Rep Power
    13

    Re: TA221 J11

    Quote Originally Posted by blackcat4866 View Post
    Is the separation roller flopping around because, maybe, the plastic post that it swivels on is busted off? =^..^=
    Hey thanks Blackcat for your reply. Hope all is well on your end.
    I replaced sep and feed rollers this morning and all corresponding parts looked to be intact.
    If I could take a stab it I would say Feeder roller is not coming in contact with paper?
    I would assume the clutch is turning the shaft and all rollers than paper should feed?
    Is feeder roller stationary or does it drop down to meet paper at some time?
    I don't see any signs of feeder roller coming in contact and moving paper at all.


  4. #4
    Master Of The Obvious 10,000+ Posts
    TA221 J11

    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    15,216
    Rep Power
    245

    Re: TA221 J11

    Quote Originally Posted by blackdog View Post
    Is feeder roller stationary or does it drop down to meet paper at some time?
    I don't see any signs of feeder roller coming in contact and moving paper at all.
    The pickup roller is spring loaded, but it's the spring loaded lift plate that lifts the paper up to the the roller. It's generally a pretty crappy feed system. IIRC the spring clutches will wrap if a paper jam isn't removed correctly. If you remove the rear cover, you can make a Sharpie mark on the end of the feed shaft, then watch to see if it rotates. My bet is that it isn't, and you need a clutch. =^..^=

    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.
    3) if you're going to ask about jams include the jam code.
    4) if you're going to ask about an error code include the error code.


    blackcat: Master Of The Obvious =^..^=

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-=-=-=-=-=-


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here