Results 1 to 6 of 6
  1. #1
    Field Supervisor 500+ Posts
    Ecosys M2535 "Please Wait" stays on LED


    Join Date
    Jan 2012
    Location
    Tulsa, Oklahoma
    Posts
    932
    Rep Power
    42

    Ecosys M2535 "Please Wait" stays on LED

    I took the controller board off and the power supply board off to see about getting to the exit gears. When I re-installed the copier comes up with "ready to copy" for about a second then goes to "Please wait" Having a ton of trouble finding info on the. I tried to re-install firmware through the usb an it won't do the firmware update. I ran a Maintenance page through U000 and the copy came out blank.. Any help would be very appreciated... Thanks

  2. #2
    Field Supervisor 500+ Posts
    Ecosys M2535 "Please Wait" stays on LED


    Join Date
    Oct 2010
    Posts
    815
    Rep Power
    45

    Re: Ecosys M2535 "Please Wait" stays on LED

    Been there and done that. Something got missed or plugged into the wrong connector. The only thing to do is take it back apart and start over being careful to get everything plugged in and into the correct connector.

  3. #3
    Master Of The Obvious 10,000+ Posts
    Ecosys M2535 "Please Wait" stays on LED

    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    22,442
    Rep Power
    462

    Re: Ecosys M2535 "Please Wait" stays on LED

    I'm thinking that you didn't reconnect something correctly.

    If it were me I'd re-do everything I did the other day, except re-connect that one thing correctly. =^..^=
    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.
    3) if you're going to ask about jams include the jam code.
    4) if you're going to ask about an error code include the error code.
    5) You are the person onsite. Only you can make observations.

    blackcat: Master Of The Obvious =^..^=

  4. #4
    Field Supervisor 500+ Posts
    Ecosys M2535 "Please Wait" stays on LED


    Join Date
    Jan 2012
    Location
    Tulsa, Oklahoma
    Posts
    932
    Rep Power
    42

    Re: Ecosys M2535 "Please Wait" stays on LED

    Thanks you guys so much... I'm doing that right now... Boy this is a time killer... THANKS AGAIN !!!

  5. #5
    Field Supervisor 500+ Posts
    Ecosys M2535 "Please Wait" stays on LED


    Join Date
    May 2009
    Location
    Concord, NH
    Posts
    770
    Rep Power
    53

    Re: Ecosys M2535 "Please Wait" stays on LED

    If you removed the main board, there are two Flex cables that you would have to re-install. Make sure that upon reinstallation that one of the lands [circuits] did not get dislodged and is now not making contact with the connector's pins. We have found that these flex cables can very easily have a land de-laminate from the cable. I would remove these flex circuits and check the ends of the cable to make sure a land has not dislodged. Also as others have suggested make sure all the connectors you removed are seated properly, have had cases where the connector appears seated only to discover that a little extra push results in you feeling the connector seat properly and unit starts working. In my case with my fat fingers, I use a jeweler's screwdriver or a spring hook tool to make sure the connectors are fully seated. Hope this helps.

  6. #6
    Field Supervisor 500+ Posts
    Ecosys M2535 "Please Wait" stays on LED


    Join Date
    Jan 2012
    Location
    Tulsa, Oklahoma
    Posts
    932
    Rep Power
    42

    Re: Ecosys M2535 "Please Wait" stays on LED

    Thanks, I just checked that. Looked ok, No missing contact on strip. I reinstalled the Control board twice now and checked every connection with the manual. I did have the USB connection on the main board switched with the scanner motor on the scan PWB. Thinking at this point I fried the controller board. Maby missed a ground when power up... I also went as far as to change both power supplies (used). No change.... Guess I need a control board....

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here