Results 1 to 5 of 5
  1. #1
    Senior Tech 100+ Posts
    8000i fuser fault after opening door


    Join Date
    Aug 2010
    Location
    minneapolis, MN
    Posts
    245
    Rep Power
    30

    8000i fuser fault after opening door

    Getting a C6720( fuser ih belt rotation error) every time any of the right side doors are opened and then closed.

    Swapped fuser with known good fuser, checked rotation sensor wire harness in fusers(per bulletin), updated firmware, replaced fuser drive motor assembly, checked connection of YC26 on engine pwb, checked for pinched wires, loose connections.

    Once the error is reset, the machine will boot, and run hundreds of prints, until it jams, once a door is opened to remove jam, closes the door, the fuser faults. Or even while the machine is sitting at ready, if I open the main large door, or either of the 2 lower doors, once closed, faults.

    Also if I press the energy saver button, the machine instantly throws a C6770 (fuser ih low electrical power)

    My next steps will be to replace the fuser ih pwb, then the engine pwb.

    Let me know

    Thanks
    MNTech

    Sent from my SM-G955U using Tapatalk

  2. #2
    Technician
    Join Date
    Nov 2012
    Location
    Solomons, MD
    Posts
    48
    Rep Power
    24

    Re: 8000i fuser fault after opening door

    Quote Originally Posted by mntech View Post
    Getting a C6720( fuser ih belt rotation error) every time any of the right side doors are opened and then closed.

    Swapped fuser with known good fuser, checked rotation sensor wire harness in fusers(per bulletin), updated firmware, replaced fuser drive motor assembly, checked connection of YC26 on engine pwb, checked for pinched wires, loose connections.

    Once the error is reset, the machine will boot, and run hundreds of prints, until it jams, once a door is opened to remove jam, closes the door, the fuser faults. Or even while the machine is sitting at ready, if I open the main large door, or either of the 2 lower doors, once closed, faults.

    Also if I press the energy saver button, the machine instantly throws a C6770 (fuser ih low electrical power)

    My next steps will be to replace the fuser ih pwb, then the engine pwb.

    Let me know

    Thanks
    MNTech

    Sent from my SM-G955U using Tapatalk
    There is a circuit board on the front of the machine. Check the connectors. I think its called Front PWB

  3. #3
    Master Of The Obvious 10,000+ Posts
    8000i fuser fault after opening door

    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    22,434
    Rep Power
    462

    Re: 8000i fuser fault after opening door

    Quote Originally Posted by mntech View Post
    ... My next steps will be to replace the fuser ih pwb, then the engine pwb.

    Let me know

    Thanks
    MNTech ...
    Overall, I like your choice.

    I would also meter out all your doorswitches (not just a service mode test, but a real Ohmmeter). =^..^=
    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.
    3) if you're going to ask about jams include the jam code.
    4) if you're going to ask about an error code include the error code.
    5) You are the person onsite. Only you can make observations.

    blackcat: Master Of The Obvious =^..^=

  4. #4
    Field Supervisor 500+ Posts
    8000i fuser fault after opening door


    Join Date
    May 2009
    Location
    Concord, NH
    Posts
    770
    Rep Power
    53

    Re: 8000i fuser fault after opening door

    Quote Originally Posted by mntech View Post
    Getting a C6720( fuser ih belt rotation error) every time any of the right side doors are opened and then closed.

    Swapped fuser with known good fuser, checked rotation sensor wire harness in fusers(per bulletin), updated firmware, replaced fuser drive motor assembly, checked connection of YC26 on engine pwb, checked for pinched wires, loose connections.

    Once the error is reset, the machine will boot, and run hundreds of prints, until it jams, once a door is opened to remove jam, closes the door, the fuser faults. Or even while the machine is sitting at ready, if I open the main large door, or either of the 2 lower doors, once closed, faults.

    Also if I press the energy saver button, the machine instantly throws a C6770 (fuser ih low electrical power)

    My next steps will be to replace the fuser ih pwb, then the engine pwb.

    Let me know

    Thanks
    MNTech

    Sent from my SM-G955U using Tapatalk
    Your next step replacements are logical. The C6770 code when going into energy saver mode however would direct me to the engine board.

  5. #5
    Senior Tech 100+ Posts
    8000i fuser fault after opening door


    Join Date
    Aug 2010
    Location
    minneapolis, MN
    Posts
    245
    Rep Power
    30

    Re: 8000i fuser fault after opening door

    Fuser IH PWB replacement resolved both issues. Thanks

    Sent from my SM-G955U using Tapatalk

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here