TASKalfa 406ci toner smudge

[kyove]

Hi Guys,

I've just finish to clean a transfer belt of a TASKalfa 406ci.
Machine has 23600 copies (23000 bw and 600 color) and 3 months of life.

Problem was toner smudges (not every print) on paper.
Transfer belt seems ok, i clean the "cleaning section" of transfer belt with vacuum.

This is the only one machine I have under my maintenance.

Usually they works well or have problems?
Client prints with low coperture (average 3.7%)..
What can I do? Maybe a defective machine?

Thank you in advance,
Kyove

[Phil B.]

Hi Guys, I've just finish to clean a transfer belt of a TASKalfa 406ci. Machine has 23600 copies (23000 bw and 600 color) and 3 months of life.
Problem was toner smudges (not every print) on paper.
Transfer belt seems ok, i clean the "cleaning section" of transfer belt with vacuum.
This is the only one machine I have under my maintenance.
Usually they works well or have problems?
Client prints with low coperture (average 3.7%)..
What can I do? Maybe a defective machine?
Thank you in advance,
Kyove

try cleaning the WHOLE machine.. not just belt.
check fuser for wear

should post the counts on all parts to give us a better idea

[JR2ALTA]

I agree it's probably the belt. Kyocera had a bulletin and released seals around the drum and dev unit. But my fix for the comet drops was belt.

But it doesnt matter they'll come back. The "3 digit". Kyocera models are costly little pigs.

[Ropariva]

We have replaced many belts under warranty in these. Keep sending the faulty ones back and they will have to improve them.

[ChuckT]

Hi Guys,

I've just finish to clean a transfer belt of a TASKalfa 406ci.
Machine has 23600 copies (23000 bw and 600 color) and 3 months of life.

Problem was toner smudges (not every print) on paper.
Transfer belt seems ok, i clean the "cleaning section" of transfer belt with vacuum.

This is the only one machine I have under my maintenance.

Usually they works well or have problems?
Client prints with low coperture (average 3.7%)..
What can I do? Maybe a defective machine?

Thank you in advance,
Kyove

We have been having the same issue. We just keep a spare, and vacuum out the cleaning section, and reuse for the next machine.

It isn't the best solution, but it keeps our customers happy. They/We don't mind the extra visits when it isn't out of our way.

[Phil B.]

Hi Guys,

I've just finish to clean a transfer belt of a TASKalfa 406ci.
Machine has 23600 copies (23000 bw and 600 color) and 3 months of life.

Problem was toner smudges (not every print) on paper.
Transfer belt seems ok, i clean the "cleaning section" of transfer belt with vacuum.

This is the only one machine I have under my maintenance.

Usually they works well or have problems?
Client prints with low coperture (average 3.7%)..
What can I do? Maybe a defective machine?

Thank you in advance,
Kyove

does this have a cleaning blade or brush?

if blade did you clean it and re-powder it?

if brush, did you vac that?

it sure would be nice if you could upload PDF's of the samples?

what does the fuser look like?

what toner OEM genuine or third party?

do the use plain paper or thick?

could it be residual gum from labels on the drums?

where is the smudge located on the paper?

so many questions so little info givne.

Phil B. 'The Dentist'

[blackcat4866]

Is there an interval? Run the largest size, 50 pgs. =^..^=

[tech07]

Install a new transfer belt. Had a few of these

[JR2ALTA]

You guys are addressing an old post. (Phil has addressed twice now, 17 months apart. hehe)

[Phil B.]

You guys are addressing an old post. (Phil has addressed twice now, 17 months apart. hehe)

my bad bro... when i posted the latest i had just come in from dodging rain drops on the E130 and still didn't get all the hay bailed. still the south 40 to do.. expecting rain all fucking week till sunday.. it'll be asshole deep to an elephant by then again!