Results 1 to 7 of 7
  1. #1
    just another tech 50+ Posts
    Join Date
    Aug 2009
    Posts
    71
    Post Thanks / Like
    Rep Power
    11

    Dumb question but please answer DF-650 on 8030

    We took over service on a KM-8030 in my territory. It's my only Kyocera I wasn't trained on because it's an older model. Please advice on how to remove the finisher DF-650 from the machine. I only had a few minutes to look, but I'm sure its easier than it appears. Advice would be appreciated.


  2. #2
    Service Manager 250+ Posts Zackuth's Avatar
    Join Date
    Aug 2009
    Location
    Arkansas
    Posts
    380
    Post Thanks / Like
    Rep Power
    16

    Re: Dumb question but please answer DF-650 on 8030

    Open the door to the finisher and you will see a black handle on the edge near the copier. Remove the screw (if it is there) and pull the handle. The finisher will seperate. On the back of the machine you will see a cord that runs to the back of the copier, unplug this and the finisher is completely disconnected from the machine. Make sure you turn the copier off if you want to disconnect the finisher or you will get error codes.


  3. #3
    just another tech 50+ Posts
    Join Date
    Aug 2009
    Posts
    71
    Post Thanks / Like
    Rep Power
    11

    Re: Dumb question but please answer DF-650 on 8030

    Thanks. I definitely figured that was it and i removed the screw on the black handle, but when i pulled, it just bent rather than pulled toward me. Maybe its just wedged in there tight or something?


  4. #4
    Service Manager 250+ Posts Zackuth's Avatar
    Join Date
    Aug 2009
    Location
    Arkansas
    Posts
    380
    Post Thanks / Like
    Rep Power
    16

    Re: Dumb question but please answer DF-650 on 8030

    Yeah, they stick at times. There is a knob or something about halfway back that I grab if I need a bit more leverage.


  5. #5
    just another tech 50+ Posts
    Join Date
    Aug 2009
    Posts
    71
    Post Thanks / Like
    Rep Power
    11

    Re: Dumb question but please answer DF-650 on 8030

    I appreciate the help.


  6. #6
    Master Of The Obvious 5,000+ Posts


    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    10,616
    Post Thanks / Like
    Rep Power
    160

    Re: Dumb question but please answer DF-650 on 8030

    Oops! Wrong answer!

    At the bottom along the same copier edge there is a metal lever with a screw through it. Remove the locking screw and lift the handle about 30 degrees from where it started.

    You see there are a couple of latches that attach to the base also, and you want to raise them just enough to clear the feature on the frame. It's a good idea to remove the ground contact leaf springs if your going to move the machine any distance. The movers will mangle them. =^..^=

    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.


    blackcat: Master Of The Obvious =^..^=

  7. #7
    just another tech 50+ Posts
    Join Date
    Aug 2009
    Posts
    71
    Post Thanks / Like
    Rep Power
    11

    Re: Dumb question but please answer DF-650 on 8030

    thanks blackcat. I did have the bottom part unscrewed and lifted but I guess the top part just stuck on me. I'm going back in the morning.


Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-=-=-=-=-=-


Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here