Thanks Thanks:  0
Dislikes Dislikes:  0
Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 22
  1. #11
    Master Of The Obvious 10,000+ Posts
    KM-6030, KM-8030

    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    16,610
    Rep Power
    275
    I've got 6 or 8 of them. So far all are underused. The only kind of calls I get are 1d10t errors. Paper guides not set right, can't install toner (could it be any easier?), can't find a paper jam in the DF650, like that. I don't think that I've had a real failure of any sort yet.

    Oh, a broken switch flag on setup (FSW3). That's it. Great machines!

    =^..^=
    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.
    3) if you're going to ask about jams include the jam code.
    4) if you're going to ask about an error code include the error code.


    blackcat: Master Of The Obvious =^..^=

  2. #12
    Senior Tech 100+ Posts
    Join Date
    Apr 2008
    Posts
    130
    Rep Power
    23

    one note

    Just look out for the fuser driving gearbox and motor in the rear of the machine these go at around a million copies.

    apart from that a good machine all round

  3. #13
    Field Supervisor 500+ Posts Jimbo1's Avatar
    Join Date
    Mar 2008
    Location
    Broken Arrow, OK
    Posts
    845
    Rep Power
    30

    J60 and J62

    So nobody has had any giving these jam codes a lot??

    We have had this problem at least two differnt locations, sure would like to hear if anybody else has seen this. Like a timing problem.

    "Some days you get the bear, some days the bear gets you."

    Cdr. William Riker

  4. #14
    Technician
    Join Date
    May 2008
    Location
    Sarasota, Fl
    Posts
    40
    Rep Power
    22
    The Jam 00 comes up after a jam has been cleared or attempted and the machine restarted. This means it still sees a jam. You need to check the Sim 034? and see which sensor is stuck. It is ususally on of the vertical conveying sensors or the fuser exit sensor. Both of these pop out of place fairly easily and stick.

    Duplex jamming has been rare for me but I have seen some. Most are not during duplexing but during switchback. Yesterday I had one where the paper was entering the switchback and the side paper guides were hitting the paper on the side and not letting it pull back up. I just widened the gap on the offending guide and no more problems.

    I have had to replace that solenoid in the swithcback and the spring and frame where the solenoid pin rides because of a groove forming and causing the solenoid to stick.

    d

  5. #15
    Technician
    Join Date
    Aug 2006
    Posts
    21
    Rep Power
    25

    Thumbs up KM6030/8030 Dulpex.

    Yep Jam 60 and jam "62" are the commpm jams in the duplex area.Have found the solenoid in the duplex area for the paper conveying section needs a good clean out from time to time.Rust develops in the solenoid and it is slow to react.also make sur the white roller in the duplex section hasnt siezed up,and is spinning freely.If it isnt just strip and clean it.There is a one way gear in the back of the duplex tray(you will have to pull the duplexing tray out of the machine to get to it.Make sure that it is clean and free from grease.Apart from that there is a switch in the switch back section that comes out from time to time.it just before the paper comes into the duplex section.Hope this helps.

  6. #16
    grumpy old git 500+ Posts banginbishop's Avatar
    Join Date
    Oct 2007
    Posts
    889
    Rep Power
    34

    km-8030

    I've got 3 or 4 of these on my area and i've set them all to 1 million on the pm cycle. The heater roller goes at about 300k but after replacing it it lasts untill the million. Main problems i have are operator errors. Right hand side door sensors being pulled off - customer slams the door from the top, not in the middle hence it knocks the sensors out of its position(giving permanent jam), pick off bar(fuser unit) not being shut down properly, transfere section damage (customer) and various other damage to the machines. All in all a fantastic bit of kit and i prefere this to a ricoh 2105 which has a lower service cycle,its faster and a bitch to work on when the toner pipe goes tits up!

  7. #17
    Junior Member
    Join Date
    Jan 2009
    Posts
    3
    Rep Power
    0
    i've recently got a job in a reprographics department with one of these machines (coupled with a DF-650 finisher).

    is there anywhere i can find a list of jam codes and what sensors might trip them?

  8. #18
    Junior Member
    Join Date
    Jan 2009
    Posts
    5
    Rep Power
    0

    Great Box

    I've been running one of these for over two years now. It's the best b/w machine I've ever had. I put around 40,000 copies a month on it, and I go six months between services -- and it's usually something minor.

    I also find that its a pretty intuitive machine; good controls -- it doesn't take a rocket scientist to run it. I'd recommend it to anyone.

  9. #19
    Field Supervisor 500+ Posts
    Join Date
    Feb 2008
    Location
    Mechanicsburg, PA
    Posts
    906
    Rep Power
    33

    Re: KM-6030, KM-8030

    NEC put their name on these...love them! A lot of off lease deals with good prices are coming around now, with low counts of 1,2,3 or so hundred thousand...awesome!

  10. #20
    juan_khu
    Guest

    Re: "00" jam KM6030

    Quote Originally Posted by Tommyc View Post
    Hey Guys,

    Have any of you seen "00" jam code on a KM6030. Technician replaced duplex switchback roller and now this jam code is permanently on machine...

    Thanks,

    Tom.
    Now I have 00 jam code on my 6030. anyone know how to solve this?
    thanks.
    juan

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-=-=-=-=-=-


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here