Results 1 to 7 of 7
  1. #1
    Senior Tech 100+ Posts
    Join Date
    Aug 2011
    Posts
    129
    Rep Power
    14

    DP-770 and lift issues

    Has anyone seen a problem where the doc feed (specifically the DP-770) on the new TASKalfa's won't lift? It doesn't cause an error code or jam it just says to reseat the paper. My hunch is the upper lift sensor is dead because both lights are activated when the tray is down. Just curious if anyone else has seen this problem.


  2. #2
    Master Of The Obvious 10,000+ Posts
    DP-770 and lift issues

    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    15,214
    Rep Power
    245

    Re: DP-770 and lift issues

    On the CS-8030 DP and the DP700 on the FalconIII, all it takes is a paper clip or curl of paper to fall down into the lift plate sensor.

    It can be intermittent because raising the DP can cause the paper clip to shift front to rear. =^..^=

    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.
    3) if you're going to ask about jams include the jam code.
    4) if you're going to ask about an error code include the error code.


    blackcat: Master Of The Obvious =^..^=

  3. #3
    Technician Robob's Avatar
    Join Date
    Dec 2011
    Location
    Atlanta, GA
    Posts
    17
    Rep Power
    12

    Re: DP-770 and lift issues

    Yep, I'm getting the same symptom on a 3500i with DP-700 not lifting. I cleaned out all the dust and paper clips (of course) but the lift motor just seems to stall sporadically. Even more frequently, now that I've cleaned everything. I'm going back with firmware, and I've ordered the lift motor and sensor for good measure.

    You guys find out anything since 2013 posts?


  4. #4
    scrub 500+ Posts jmaister's Avatar
    Join Date
    Aug 2010
    Location
    somewhere
    Posts
    551
    Rep Power
    21

    Re: DP-770 and lift issues

    dp770-b.jpg

    see that little stopper? If that is bent, it will effect the accuracy of your lift motor. AND you cant test the lift motor accurately in maintenance mode with this buggered as well.

    Just my 2 cents.

    An idling develper is not a healthy developer.

  5. #5
    Field Supervisor 1,000+ Posts subaro's Avatar
    Join Date
    Oct 2010
    Posts
    1,129
    Rep Power
    30

    Re: DP-770 and lift issues

    Remove the pickup roller assy and examine the plastic block[this is the assy that sits on the dp cover]. One of the projections get broken off and does not actuate the lift sensor. A tech had this problem at the shop and changed almost everything including dp board,motor and sensor. A call to one of the road techs pointed out the solution as i mentioned earlier.

    THE ONLY THING FOR EVIL TO TRIUMPH IS FOR GOOD MEN TO DO NOTHING..........edmund burke

  6. #6
    Junior Member
    Join Date
    Sep 2012
    Location
    Danvers
    Posts
    6
    Rep Power
    0

    Re: DP-770 and lift issues

    Thanks that was it. So happy I found this post


  7. #7
    Junior Member egpatl's Avatar
    Join Date
    Sep 2008
    Location
    duluth
    Posts
    5
    Rep Power
    0

    Re: DP-770 and lift issues

    Hey guys, we have had this problem several times if you go to simulation 243 then open top cover of the feeder and cheat the interlock with the cover open run the lift option if the lift tray works it's the holder ass'y causing the problem (it's the black housing that holds the feed belt and the lead feed roller) take it out and make sure the flag and the latch on the front of the ass'y are still in place if either one of those are broken it will not lift.


Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-=-=-=-=-=-


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here