Thanks Thanks:  0
Dislikes Dislikes:  0
Results 1 to 7 of 7
  1. #1
    Technician RoyROd's Avatar
    Join Date
    Mar 2013
    Location
    Del Rio, TX
    Posts
    29
    Rep Power
    23

    Kyocera TaskAlfa 4501i Error Code

    I've got a week old TaskAlfa 4501i that was giving me intervals of C0640 and F357 error codes. After speaking with Kyocera tech support they told me to upgrade firmware, reseat memory DIMMs and reseat the HDD. After doing all these, to no avail, they finally told to run a U024 which initializes the HDD. After doing so the machine came back up with an F345 code. Tech support has had me redo firmware, try individually install firmware, all to no avail. Has anyone seen something like this and if so do they have any advice?

  2. #2
    Service Manager 250+ Posts kkendric's Avatar
    Join Date
    Apr 2009
    Location
    Orlando, Florida
    Posts
    301
    Rep Power
    35

    Re: Kyocera TaskAlfa 4501i Error Code

    You could try changing the Hard drive data cable(SATA) and if that does not work replace the Hard drive.

  3. #3
    Master Of The Obvious 10,000+ Posts
    Kyocera TaskAlfa 4501i Error Code

    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    22,434
    Rep Power
    462

    Re: Kyocera TaskAlfa 4501i Error Code

    I'd have changed the HDD by now.

    C0640: HDD failure
    CF35x: An error is detected at the Print control section. 1) Reformat HDD U024 FULL; 2) Initialize backup memory U021; 3) Repl main PWB; 4) Repl HDD;
    CF34x: An error is detected at the Panel management section. 1) Reseat connectors: main PWB-YC12, YC17, YC30; Op Panel-YC1 YC2, YC3; 2) Reformat HDD U024 FULL; 3) Initialize backup memory U021; 4) Repl Op panel PWB; 5) Repl main PWB;

    =^..^=
    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.
    3) if you're going to ask about jams include the jam code.
    4) if you're going to ask about an error code include the error code.
    5) You are the person onsite. Only you can make observations.

    blackcat: Master Of The Obvious =^..^=

  4. #4
    Enscoe09
    Guest

    Question Re: Kyocera TaskAlfa 4501i Error Code

    Hello,

    Was there any resolution to this F345 error code? Experiencing "F345" error code on the 3252ci Kyocera. Customer was getting a white screen in the morning. updated firmware and then started getting F345 error code in the morning. The customer has to shut the device down and turn it back on and it will work ok.(there were a lot of other weird things going on such as power inconsistencies and paper jams about 3 other error codes, but these were resolved either from what we tried below or by switching the power to a new outlet. This device is in a large commercial building with high security and for whatever reason it is hard to find the electrical schematics. customer was also pulling the plug of the machine to fresolve the white screen in the morning rather than using the rocker switch which COULD have caused more problems as well) At some point through the evening, the machine gets the F345 error code while it is sitting overnight.


    Tried to reload the firmware. reformatted hard drive (while reformatting hard drive could not complete backup because the files pulled from hard drive were corrupt. Had to manually re-configure unit for client. Reseated DIMMS and connector units. Replaced the main PWB. Still receiving F345 error every morning.


    Per Kyocera tech support, the F345 error code is not in the service manual. Hard to believe that Kyocera tech support has not heard of this code? I am trying to do my due diligence versus just throwing parts at the machine.



    Thank you kindly,

    Ashley

  5. #5
    Senior Tech 250+ Posts
    Join Date
    Apr 2017
    Location
    Manitoba
    Posts
    348
    Rep Power
    20

    Re: Kyocera TaskAlfa 4501i Error Code

    Hi,
    Per the service manual: Where X is any number or letter...

    F34X Abnormality detecting in the Panel Management
    Department
    1. Check the harness between Panel<=>Main boards, and the
    connection state of a connector, and perform an operation
    check.
    * Notes
    2. Initialize HDD and perform an operation check.
    (FULL of U024) *
    3. U021 Controller backup initialization is carried out and an operation
    check is performed.
    4. Exchange a Panel board and perform an operation check.
    * Notes
    5. Exchange a Main board and perform an operation check.
    6. Get USBLOG and contact service headquarters.
    * Only HDD standard model
    * Note : A Dual Core CPU model and HyPAS model
    *********************************

    Is a cable pinched or FFC cable conductor peeled-back inside connector?

  6. #6
    Junior Member mman's Avatar
    Join Date
    Feb 2015
    Posts
    1
    Rep Power
    0

    Re: Kyocera TaskAlfa 4501i Error Code

    Replace the HDD

  7. #7
    certified scrub 500+ Posts
    Kyocera TaskAlfa 4501i Error Code

    jmaister's Avatar
    Join Date
    Aug 2010
    Location
    somewhere i prefer not to share
    Posts
    754
    Rep Power
    41

    Re: Kyocera TaskAlfa 4501i Error Code

    why is this so much like the iR ADV 2nd gen?

    1. error code corresponding to HDD, change the HDD

    2. screen freezing on start up, change the HDD

    atleast Kyocera HDD is your normal mobile HDD.
    Idling colour developers are not healthy developers.

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here